相关论文: Effects of compocasting process parameters on micr…
Samples of $\alpha$-SiC have been sintered with liquid phase (LPS) to 1950 $^\circ$C, in atmosphere of argon and processing times between 1 and 7 hours. Using scanning electron microscopy (SEM) the microstructure of the samples has been…
We show here for the first time the use of a cold sintering process (CSP) to sinter CoSb3-based thermoelectric materials. CSP at 150 {\deg}C for 90 min under a uniaxial pressure of 750 MPa yields pieces with a relative density of 86 %,…
We aim to investigate relationships between select processing parameters or inputs (composition, temperature, annealing time) and two structural parameters, specifically, the mean radius and volume fraction of the Fe$_3$Si nanocrystals. To…
Thin films of superconducting V$_3$Si were prepared by means of RF sputtering from a compound V$_3$Si target at room temperature onto sapphire and oxide-coated silicon wafers, followed by rapid thermal processing under secondary vacuum. The…
Precursor powders of BaMg2-xCoxFe16O27 with (x = 0.0, 1.0, and 2.0) were prepared using high-energy ball milling, and the effects of chemical composition and sintering temperature on the structural and magnetic properties were investigated…
A three-dimensional model of a partially melted powder bed with particles stochastically distributed in size and space coordinates has been developed. Numerical simulation of temperature distributions in stainless steel AISI 316L and…
The remarkable finding of this work is the linear correlation between the critical temperature of superconducting (SC) transition, Tc, and the room-temperature half-width of angular correlation of positron annihila- tion phonons (ACPAP),…
The effect of sintering regimes on the density, microstructure parameters, and mechanical properties of Al2O3 and Al2O3 + 0.25%MgO ceramics has been investigated. The ceramics were sintered in three regimes: Regime I - heating at a constant…
A coarse-grained molecular dynamics model of linear polyethylene-like polymer chain system was built to investigate the responds of structure and mechanical properties during uniaxial deformation. The influence of chain length, temperature,…
The changes of magnetic properties upon heat treatment of a metastable supersaturated solid solution processed by severe plastic deformation are investigated by in-situ AC-hysteresis measurements. Data are analyzed in the framework of…
Si hyperdoped with chalcogens (S, Se, Te) is well-known to possess unique properties such as an insulator-to-metal transition and a room-temperature sub-bandgap absorption. These properties are expected to be sensitive to a post-synthesis…
In the present study, superheating treatment has been applied on A357 reinforced with 0.5 wt. % (Composite 1) and 1.0 wt.% (Composite 2) continuous stainless steel composite. In Composite 1 the microstructure displayed poor bonding between…
Effects of substrate temperature, substrate wettability and particles concentration are experimentally investigated for evaporation of a sessile water droplet containing colloidal particles. Time-varying droplet shapes and temperature of…
We optimize the superconducting properties of Sm-based oxypnictide (Sm1111: SmFeAsO0.80F0.20) by using the Spark Plasma Sintering (SPS) technique under various synthesis conditions, including heating temperatures ranging from 600 to 1000…
Aluminosilicate (Al-Si-O) thin films containing up to 31 at. % Al and 23 at. % Si were prepared by reactive RF magnetron co-sputtering. Mechanical and structural properties were measured by indentation and specular reflectance infrared…
From in-situ ellipsometric measurements during condensation of As4 molecular beam on GaAs(001) substrate the arsenic sticking coefficient was determined. For the substrate with Ga-rich surface reconstruction at 60C the sticking coefficient…
Room and high temperature mechanical properties of reactive magnetron sputtered TaSiN coatings were measured using nanoindentation (between 25C and 500C). Fracture toughness was also evaluated at a similar temperature range using the…
We prepared very high-coercivity cobalt ferrite nanoparticles using short-time high-energy mechanical milling. After the milling process, the coercivity of the nanoparticles reached 3.75 kOe - a value almost five times higher than that…
Novel algorithm for designing values of technological parameters for production of Soft Magnetic Composites (SMC) has been created. These parameters are the following magnitudes: hardening temperature $T$ and compaction pressure $p$. They…
The effect of sintering temperatures (Ts) on the structural and magnetic properties of Ni0.6Zn0.4Fe2O4 (NZFO) ferrites synthesized by conventional double sintering method has been reported. The samples are sintered at 1200, 1250 and 1300…