相关论文: Effect of cold rolling strain on the microstructur…
The influence of the physical mechanisms activated during deformation and annealing on the microstructure and texture evolution as well as on the mechanical properties in the equiatomic CoCrFeMnNi high-entropy alloy (HEA) were investigated.…
The effect of composition on microstructure both at the length scale of the secondary dendrite arm spacing and nano-sized dispersoids during homogenization of Al-Zn-Cu-Mg-Zr alloys has been studied. A comprehensive model that can predict…
We provide a critical atomistic evidence of pseudoelastic behavior in complex solid-solution BCC Mo-W-Ta-Ti-Zr alloy. Prior to this work, only limited single-crystal BCC solids of pure metals and quaternary alloys have shown pseudoelastic…
Refractory multi-principal element alloys (MPEAs) are key research focus for excellent high-temp properties and engineering potential. Deformation mechanisms/mechanical behaviors of quaternary NbTaTiZr MPEA under high strain rates/extreme…
One of the main material properties altered by rare earth additions in magnesium alloys is texture, which can be specifically adjusted to enhance ductility and formability. The current study aims at illuminating the texture selection…
Three novel precipitation strengthened bcc alloys which exhibit a smooth microstructural gradient with composition have been fabricated in bulk form by induction casting. All three alloys are comprised of a mixture of disordered A2-(Fe, Cr)…
In the present investigation, a strongly bonded strip of an aluminium-magnesium based alloy AA5086 is successfully produced through accumulative roll bonding (ARB). A maximum of up to eight passes has been used for the purpose.…
This study explores Ti-containing complex concentrated alloys (CCAs) within the AlMoNbTiZr system, focusing on compositions located in regions of the Bo-Md diagram characterized by low bond order (Bo) and d-orbital energy level (Md). Four…
Monophasic and homogeneous Ni10Zr7 nanocrystalline alloy films were successfully grown at room temperature by co-sputtering in an indigenously developed three-gun DC/RF magnetron sputtering unit. The films could be produced with long-range…
Components manufactured via Wire + Arc Additive Manufacturing are usually characterised by large columnar grains. This can be mitigated by introducing in-process cold-rolling; in fact, the associated local plastic deformation leads to a…
Understanding alloy phase transformations during continuous cooling is important for post-processing design and optimization. In this work, continuous-cooling-transformation (CCT) diagrams of Inconel 718 alloys manufactured by laser powder…
Dendritic microstructures are frequently observed in as-solidified refractory high-entropy alloys (RHEAs), and their homogenization typically requires a long-term heat treatment at extremely high temperatures. High-pressure torsion (HPT)…
Phase diagrams supported by density functional theory methods can be crucial for designing high-entropy alloys that are subset of multi-principal$-$element alloys. We present phase and property analysis of quinary…
Even if the atoms of a multicomponent alloy occupy a common lattice, their distribution is not homogeneous, and regions with different compositions can be detected. Three representative examples will be discussed: a Cantor-type system…
Interfacial segregation and chemical short-range ordering influence the behavior of grain boundaries in complex concentrated alloys. In this study, we use atomistic modeling of a NbMoTaW refractory complex concentrated alloy to provide…
The yielding transition, structural relaxation, and mechanical properties of metallic glasses subjected to repeated loading are examined using molecular dynamics simulations. We consider a poorly-annealed Cu-Zr amorphous alloy periodically…
The cyclic deformation behavior of extruded Mg-8.5wt.%Al alloy with a conventional extrusion texture and a modified texture is systematically investigated by in-situ neutron diffraction and elastic viscoplastic self-consistent (EVPSC)…
The effect of pre-ageing deformation on the size and distribution of beta-prime precipitates and subsequently on the resulting strength and ductility have been measured in a Mg-3.0at.%Zn-0.5at.%Y alloy. The alloy was extruded and then…
New approaches for the design of alloy systems with multiprincipal elements is recently researched in refractory materials field. However, most research aimed at arc melting process with weakness of coarsening of grains and inhomogeneous…
The intermetallic compound Zr3Al is severely deformed by the method of repeated cold rolling. By X-ray diffraction it is shown that this leads to amorphization. TEM investigations reveal that a homogeneously distributed debris of very small…