相关论文: Coupled plastic strain- and stress-induced phase t…
Rough diamond anvils (rough-DA) are introduced to intensify all occurring processes during an in-situ study of heterogeneous compression of strongly pre-deformed Zr in diamond anvil cell (DAC). Crystallite size and dislocation density of Zr…
Various phenomena (phase transformations, chemical reactions, and friction) under high pressures in diamond anvil cell are strongly affected by fields of all components of stress and plastic strain tensors. However, they could not be…
The first in situ quantitative synchrotron X-ray diffraction (XRD) study of plastic strain-induced phase transformation (PT) has been performed on $\alpha-\omega$ PT in ultra-pure, strongly plastically predeformed Zr as an example, under…
The Fe-Mn-based alloys are receiving immense attention due to their applications in the third generation of advanced high-strength steels, owing to their high strength and ductility. A detailed in situ high-pressure structural phase…
Plastic strain-induced phase transformations (PTs) and chemical reactions under high pressure are broadly spread in modern technologies, friction and wear, geophysics, and astrogeology. However, because of very heterogeneous fields of…
Study of the plastic flow and strain-induced phase transformations (PTs) under high pressure with diamond anvils is important for material and geophysics. We introduce rough diamond anvils and apply them to Zr, which drastically change the…
Processes involving severe plastic deformations (SPD) and phase transformations and chemical reactions (PTs/CRs) under high pressures are widespread for obtaining new nanostructured phases and their processing, mechanochemical synthesis,…
In situ studies under severe plastic deformation at high pressures, employing rotational/shear diamond anvil cells (RDAC), have recently gained much interest in the high-pressure community owing to their potential applications in material…
Deep-focus earthquakes that occur at 350-660 km are theorized to be caused by strain-induced olivine-spinel phase transformation (PT). We introduce and apply dynamic rotational diamond anvil cell with rough diamond anvils to deform San…
Pressure-induced phase transformations (PTs) between numerous phases of Si, the most important electronic material, have been studied for decades. This is not the case for plastic strain-induced PTs. Here, we revealed in-situ various…
The microstructure and mechanical properties of materials saturate to steady states after severe plastic deformation (SPD). Despite the well-known effect of temperature on the steady-state microstructure, there is no general agreement on…
Plastic flow behavior of low carbon steel has been studied at room temperature during tensile deformation by varying the initial strain rate of 3.3x10e-4 1/sec to the final strain rate ranging from 1.33x10e-3 1/sec to 2.0x10e-3 1/sec at a…
We present a combined experimental and theoretical study on the quasi-one-dimensional organic conductor (TMTTF)$_2$PF$_6$, and elucidate the variation of its physical properties under pressure. We fully resolve the crystal structure by…
Double stage diamond anvil cells (DAC) of two designs have been assembled and tested. We used a standard symmetric DAC as a primary stage and CVD microanvils machined by a focused ion beam - as a second. We evaluated pressure, stress, and…
High-pressure torsion (HPT), a technique of severe plastic deformation (SPD), is shown as a promising processing method for exchange-spring magnetic materials in bulk form. Powder mixtures of Fe and SmCo$_{5}$ are consolidated and deformed…
We conduct dislocation dynamics (DD) simulations of Fe periodic single crystals under tensile load at several high strain rates and temperatures. The simulations are enabled by the recent development of temperature-dependent dislocation…
Here we use large-scale molecular dynamics (MD) simulations of the high-rate deformation of nanocrystalline tantalum to investigate the processes associated with plastic deformation for strains up to 100%. We use initial atomic…
A variety of severe plastic deformation (SPD) techniques have been developed to process materials to high strains and impart microstructural refinement. High pressure torsion (HPT) is one technique that imparts inhomogeneous strain to…
A FePd alloy was nanostructured by severe plastic deformation following two different routes: ordered and disordered states were processed by high pressure torsion (HPT). A grain size in a range of 50 to 150 nm is obtained in both cases.…
A clear understanding of the dynamic behavior of metals is critical for developing superior structural materials as well as for improving material processing techniques such as cold spray and shot peening. Using a high velocity (from 120…