相关论文: Processing and mechanical properties of novel biod…
Biodegradable and biocompatible 3D printable biomaterials with tunable mechanical properties and degradation rate adapted to target tissues were urgently required to manufacture scaffolds for tissue regeneration. Herein, a strategy based on…
Open-porous scaffolds of WE43 Mg alloy with a body-center cubic cell pattern were manufactured by laser powder bed fusion with different strut diameters. The geometry of the unit cells was adequately reproduced during additive manufacturing…
Zinc alloys have emerged as promising candidates for biodegradable materials due to their remarkable biocompatibility and favorable mechanical characteristics. The incorporation of alloying elements plays an essential role in advancing the…
A key issue for the fabrication of scaffolds for tissue engineering is the development of processing techniques flexible enough to produce materials with a wide spectrum of solubility (bioresorption rates) and mechanical properties matching…
In osteochondral tissue engineering (OCTE), simultaneously regenerating subchondral bone and cartilage tissue presents a significant challenge. Multiphasic scaffolds were created and manufactured using 3D printing to address this issue.…
Zinc alloys are recognised for their excellent biocompatibility and favourable corrosion rates, making them suitable for bioabsorbable implants. However, their mechanical properties necessitate improvement to fulfil the rigorous…
Fabrication of tissue engineering scaffolds with tailored physicochemical and biological characteristics is a relevant task in biomedical engineering. The present work was focused at the evaluation of the effect of fabrication approach…
In order to increase the bone forming ability of MBG-PCL composite scaffold, microporosity was created in the struts of 3D-printed MBG-PCL scaffolds for the manufacturing of a construct with a multiscale porosity consisting of meso-, micro-…
In this publication we describe the extrusion process and the properties of polymer-bonded anisotropic SrFe$_\text{12}$O$_\text{19}$ filaments for fused filament fabrication (FFF). Highly filled polyamide 12 filaments with a filling…
In this research, we present a simple and cost effective soft lithographic process to fabricate PLA scaffolds for tissue engineering. In which, the negative photoresist JSR THB-120N was spun on a glass subtract followed by conventional UV…
Dilute Mg-Zn wires are of great interest for biodegradable small-bone fixation, as magnesium degradation can support bone-related processes, while low zinc additions may provide biological benefits without compromising biocompatibility. In…
The article describes fabrication and properties of composite fibrous scaffolds obtained by electrospinning of the solution of poly({\epsilon}-caprolactone) and arginine in common solvent. The influence of arginine content on structure,…
Although 3D printing has the potential to transform manufacturing processes, the strength of printed parts often does not rival that of traditionally-manufactured parts. The fused-filament fabrication method involves melting a…
The goal of this paper is to enable 3D printed lightweight composite foams by blending hollow glass micro balloons (GMB) with high density polyethylene (HDPE). To that end, lightweight feedstock for printing syntactic foam composites is…
To simultaneously achieve high hardness and high toughness in protective coatings remains a fundamental challenge. Here, we harness the superlattice architecture to combine Koehler hardening while the coherent interfaces reduce the crack…
Four series of PLA based composite films containing horizontally aligned few layer graphene (FLG) flakes of high aspect ratio and adsorbed albumin are prepared. The mechanical and thermal properties vary with percentage, dispersion degree…
Scaffolds have a key role in the clinical success of tissue engineering for the regeneration of damaged tissues. Their bio-performance is often described as the extent to which they can provide an extracellular matrix-like environment for…
The regeneration of oral and craniofacial bone defects ranging from minor periodontal and peri-implant defects to large and critical lesions imposes a substantial global health burden. Conventional therapies are associated with several…
Three-dimensional hierarchical ZnO films with lotus-leaf-like micro/nano structures were successfully fabricated via a biomimetic route combining sol-gel technique, soft lithography and hydrothermal treatments. PDMS mold replicated from a…
Four-dimensional (4D) printing, a new technology emerged from additive manufacturing (3D printing), is widely known for its capability of programming post-fabrication shape-changing into artifacts. Fused deposition modeling (FDM)-based 4D…