相关论文: Kerr enhanced backaction cooling in magnetomechani…
Cooling a mesoscopic mechanical oscillator to its quantum ground state is elementary for the preparation and control of low entropy quantum states of large scale objects. Here, we pre-cool a 70-MHz micromechanical silica oscillator to an…
We investigate the quantum synchronization phenomena of two mechanical oscillators of different frequencies in two optomechanical systems under periodically modulating cavity detunings or driving amplitudes, which can interact mutually…
Quantum manipulation of coupled mechanical resonators has become an important research topic in optomechanics because these systems can be used to study the quantum coherence effects involving multiple mechanical modes. A prerequisite for…
Preparing and manipulating quantum states of mechanical resonators is a highly interdisciplinary undertaking that now receives enormous interest for its far-reaching potential in fundamental and applied science. Up to now, only nanoscale…
It is well-known that the nonlinear coupling between a mechanical oscillator and a superconducting oscillator or optical cavity can be used to generate a Kerr-nonlinearity for the cavity mode. We show that the strength of this…
Cavity cooling of an atom works best on a cyclic optical transition in the strong coupling regime near resonance, where small cavity photon numbers suffice for trapping and cooling. Due to the absence of closed transitions a straightforward…
We explore the physics of optomechanical systems in which an optical cavity mode is coupled parametrically to the square of the position of a mechanical oscillator. We derive an effective master equation describing two-phonon cooling of the…
Exploiting quantum effects of mechanical motion, such as backaction evading measurements or squeezing, requires preparation of the oscillator in a high-purity state. The largest state purities in optomechanics to date have relied on…
A pulsed cooling scheme for optomechanical systems is presented that is capable of cooling at much faster rates, shorter overall cooling times, and for a wider set of experimental scenarios than is possible by conventional methods. The…
Preparing mechanical systems in their lowest possible entropy state, the quantum ground state, starting from a room temperature environment is a key challenge in quantum optomechanics. This would not only enable creating quantum states of…
Current research on micro-mechanical resonators strives for quantum-limited detection of the motion of macroscopic objects. Prerequisite to this goal is the observation of measurement backaction consistent with quantum metrology limits.…
Preparing a massive mechanical resonator in a state with quantum limited motional energy provides a promising platform for studying fundamental physics with macroscopic systems and allows to realize a variety of applications, including…
Thermal noise is a major obstacle to observing quantum behavior in macroscopic systems. To mitigate its effect, quantum optomechanical experiments are typically performed in a cryogenic environment. However, this condition represents a…
Feedback is a powerful and ubiquitous technique both in classical and quantum system control. Its standard implementation relies on measuring the state of a system, processing the classical signal, and feeding it back to the system. In…
The radiation pressure of light can act to damp and cool the vibrational motion of a mechanical resonator. In understanding the quantum limits of this cooling, one must consider the effect of shot noise fluctuations on the final thermal…
Experiments in the field of optomechanics do not yet fully exploit the photon polarization degree of freedom. Here experimental results for an optomechanical interaction in a polarization nondegenerate system are presented and schemes are…
Cavity optomechanics is a tool to study the interaction between light and micromechanical motion. Here we observe near-quantum limited optomechanical physics in a truly macroscopic oscillator. As the mechanical system, we use a mm-sized…
We consider a cavity optomechanical cooling configuration consisting of a mechanical resonator (denoted as resonator b) and an electromagnetic resonator (denoted as resonator a), which are coupled in such a way that the effective resonance…
Precision measurement of non-linear observables is an important goal in all facets of quantum optics. This allows measurement-based non-classical state preparation, which has been applied to great success in various physical systems, and…
We discuss how the optomechanical coupling provided by radiation pressure can be used to cool macroscopic collective degrees of freedom, as vibrational modes of movable mirrors. Cooling is achieved using a phase-sensitive feedback-loop…