相关论文: Transverse mode instability and thermal effects in…
Transverse Mode Instability (TMI) which results from dynamic nonlinear thermo-optical scattering is the primary limitation to power scaling in high-power fiber lasers and amplifiers. It has been proposed that TMI can be suppressed by…
We use a detailed numerical model of stimulated thermal Rayleigh scattering to compute mode instability thresholds in Tm$^{3+}$-doped fiber amplifiers. The fiber amplifies 2040 nm light using a 790 nm pump. The cross-relaxation process is…
Dependence of mode instabilities (MI) on ytterbium dopant concentrations in high power fiber amplifiers has been investigated. It is theoretically shown that, by only varying the fiber length to maintain the same total small-signal pump…
We report on detailed in-situ distributed temperature measurements inside a high power fiber amplifier. The deducted thermal load and the TMI-threshold of a commercial LMA fiber with 25 micron core and 400 micron cladding was measured at…
We present detailed studies of the effect of polarization on thermal-induced mode instability (MI) in ytterbium-doped fiber amplifiers. Based on a steady-state theoretical model, which takes both electric fields along the two principal axes…
High-power fiber laser amplifiers have enabled an increasing range of applications in industry, medicine and defense. The power scaling for narrow-band amplifiers is currently limited by the transverse modal instability. Various techniques…
We study the transverse mode instability (TMI) in the limit where a single higher-order mode (HOM) is present. We demonstrate that when the beat length between the fundamental mode and the HOM is small compared to the length scales on which…
Thermal effects are critical constrains for developing high-power thulium-doped fiber lasers (TDFLs). In this paper, we numerically investigate the lasing and thermal characteristics of the TDFLs under different pump transitions. Our…
Thulium-doped fibers suitable for core-pumped single-frequency lasers were fabricated by the modified chemical vapor deposition (MCVD) method. Refractive index profile, doping profile and spectral absorption was measured. High doping…
In this work we analyze the power scaling potential of amplifying multicore fibers (MCFs) used in coherently-combined systems. In particular, in this study we exemplarily consider rod-type MCFs with 2x2 up to 10x10 Ytterbium doped cores…
Fiber lasers are widely used in various fields owing to their high efficiency, flexible transmission and excellent beam quality. In applications such as industrial manufacturing and defense systems, a higher output power is always desired.…
We report on a monolithic thulium fiber laser with 567 W output power at 1970 nm, which is the highest power reported so far directly from a thulium oscillator. This is achieved by optimization of the splice parameters for the active fiber…
We show by numerical modeling that saturation of the population inversion reduces the stimulated thermal Rayleigh gain relative to the laser gain in large mode area fiber amplifiers. We show how to exploit this effect to raise mode…
A thulium-doped fiber laser operating quasi-continuous-wave generated 198 W of instantaneous output power in 0.2-ms pulses at 50 Hz repetition rate. The duty cycle becomes 1% and the average output power 2.0 W. This was cladding-pumped with…
In this contribution we investigate the transversal mode instability behavior of an ytterbium doped commercial 20/400 fiber and obtain 2.9 kW of output power after optimizing the influencing parameters. In this context, we evaluate the…
The ultrashort pulse laser operation is crucially defined by engaging explicit modulators. Conventionally, they are laborious to incorporate into an all-fibre design or involve the design of sophisticated cavities. We exploit Thulium-doped…
Structured-core thulium-doped fibers were developed to reduce heat load, enable shorter-wavelength operation, and achieve a pedestal-free design. In a proof-of-principle experiment, laser slope efficiencies of 52% at 1907 nm and 54% at 1940…
We show by detailed numerical modeling that stimulated thermal Rayleigh scattering can account for the modal instability observed in high power fiber amplifiers. Our model illustrates how the instability threshold power can be maximized by…
We investigated the effct of pump wavelength on the modal instabilities (MI) in high power linearly-polarized Yb-doped fiber amplifiers. We built a novel semi-analytical model to determine the frequency coupling characteristics and power…
We develop a high-power narrow-linewidth fiber amplifier based on a tapered Yb-doped fiber. In the experiment, the narrow end of the tapered fiber is used as the input port of both pump source and signal light to form a robust all-fiber…