相关论文: Effect of alloying and microstructure on formabili…
In situ neutron diffraction of the uniaxial tension test was used to study the effect of the surrounding matrix microstructure on the mechanical stability of retained austenite in high-carbon bearing steels. Comparing the samples with…
We use the phase-field method to study the martensitic transformation at the nanoscale. For nanosystems such as nanowires and nanograins embedded in a stiff matrix, the geometric constraints and boundary conditions have an impact on…
Austenite reversion during tempering of a Fe-13.6Cr-0.44C (wt.%) martensite results in an ultrahigh strength ferritic stainless steel with excellent ductility. The austenite reversion mechanism is coupled to the kinetic freezing of carbon…
The High Nitrogen Martensitic Stainless Steel (HNMS) was subjected to three different austenitizing cycles of 1050$^\circ$C, 1075$^\circ$C and 1100$^\circ$C followed by subzero treatment at -70$^\circ$C. The fraction of retained austenite…
Transformation induced plasticity (TRIP) behavior was studied in steel with composition Fe-0.07C-2.85Si-15.3Mn-2.4Al-0.017N that exhibited two TRIP mechanisms. The initial microstructure consisted of both {\epsilon}- and…
A novel medium Mn steel of composition Fe-12Mn-4.8Al-2Si-0.32C-0.3V was manufactured with 1.09 GPa yield strength, 1.26 GPa tensile strength and 54% elongation. The thermomechanical process route was designed to be industrially translatable…
In this work, we investigate the sensitivity of the microstructure and mechanical properties of an ultrafast heat treated low carbon-steel to the peak temperature. In all studied cases, the steel was heated within the intercritical…
A medium Mn steel of composition Fe-4.8Mn-2.8Al-1.5Si-0.51C (wt.\%) was processed to obtain two different microstructures representing two different approaches in the hot rolling mill, resulting in equiaxed vs. a mixed equiaxed and lamellar…
Steel, traditionally valued for its structural strength, emerges in this study as a remarkable material for exploring novel magnetic phenomena. We investigate how common processing techniques-thermal treatments and mechanical…
A large body of literature within the additive manufacturing (AM) community has focused on successfully creating stable tungsten (W) microstructures due to significant interest in its application for extreme environments. However,…
The onset of plasticity in quenched martensitic microstructures is characterized by a low initial yield stress followed by an extremely strong initial hardening response, and then a sudden hardening saturation. Literature attributes this…
This work explains the occurrence of transformation-induced plasticity via stress-assisted martensite, when designing ultrafine-grained duplex steels. It is found that, when the austenite is reduced to a fine scale of about 300 nm, the…
This work focuses on the effect of soaking time on the microstructure during ultrafast heat treatment of a 50% cold rolled low carbon steel with initial ferritic-pearlitic microstructure. Dilatometry analysis was used to estimate the effect…
A novel concept of varying the strain hardening rate of a medium Mn steel with 8 wt\% Mn by varying the duration of the intercritical anneal after hot rolling was explored. It was found that the stability of the austenite phase showed an…
Severe plastic deformation of powder blends consisting of SmCo5-Cu results in magnetically hardened nanocomposite bulk materials. The microstructure is continuously refined with increasing torsional deformation, yet, coercivity saturates at…
Microstructural features and mechanical properties of an Al-Mg-Si alloy processed by high-pressure torsion have been investigated using transmission electron microscopy, X-ray diffraction, three-dimensional atom probe, tensile tests and…
Deformation heterogeneities within microstructures of polycrystalline shape memory alloys (SMAs) during superelastic stressing are studied using both experiments and simulations. In situ X-ray diffraction, specifically the far-field high…
Effectiveness of galaxite (Al2O3MnO) and manganese oxide (MnO2) in nucleating acicular ferrite was demonstrated in a steel with composition of Fe-13.92Mn-4.53Al-1.28Si-0.11C. The hot rolled and quenched steel had a duplex microstructure of…
A novel medium manganese steel named Novalloy with composition Fe-8.3Mn-3.8Al-1.8Si-0.5C-0.06V-0.05Sn was developed and thermomechanically processed through hot rolling and intercritical annealing. The steel possessed a yield strength of 1…
In the drive towards higher strength alloys, a diverse range of alloying elements is employed to enhance their strength and ductility. Limited solid solubility of these elements in steel leads to segregation during casting which affects the…