相关论文: The high temperature mechanical properties and the…
A Twinning Induced Plasticity (TWIP) steel with a nominal composition of Fe-16.4Mn-0.9C-0.5Si-0.05Nb-0.05V was deformed to an engineering strain of 6\%. The strain around the deformation twins were mapped using the 4D-STEM technique. Strain…
A medium Mn steel of composition Fe-4.8Mn-2.8Al-1.5Si-0.51C (wt.\%) was processed to obtain two different microstructures representing two different approaches in the hot rolling mill, resulting in equiaxed vs. a mixed equiaxed and lamellar…
A new $\beta$-metastable Ti-alloy is designed with the aim to obtain a TWIP alloy but positioned at the limit between the TRIP/TWIP and the TWIP dominated regime. The designed alloy exhibits a large ductility combined with an elevated and…
The present work reported a novel L12-strengthening NiCoCrAlTi high entropy alloy (HEA) with an outstanding synergy of tensile strength and ductility at both ambient and high temperatures. Transmission electron microscopy (TEM)…
High-manganese twinning-induced plasticity (TWIP) steels exhibit high strain hardening, high tensile strength, and high ductility, which make them attractive for structural applications. At low tensile strain rates, TWIP steels are prone to…
Aiming at increasing the yield strength of transformation and twinning induced plasticity (TRIP and TWIP) titanium alloys, a dual-phase $\alpha$/$\beta$ alloy is designed and studied. The composition Ti 7Cr 1.5Sn (wt.%) is proposed, based…
This chapter presents a literature review of the serrated flow phenomenon in high-entropy alloys (HEAs). The serrated flow is important as it can result in permanent macroscopic and microstructural changes in HEAs. The literature reveals…
We investigate the strain-rate-dependent mechanical behavior and deformation mechanisms of a refractory high entropy alloy, Ti29Zr24Nb23Hf24 (at.%), with a single-phase body-centered cubic (BCC) structure. High-temperature compression tests…
High-entropy alloys (HEAs) stand out between multi-component alloys due to their attractive microstructures and mechanical properties. In this investigation, molecular dynamics (MD) simulation and machine learning were used to ascertain the…
Metastable alloys with transformation/twinning-induced plasticity (TRIP/TWIP) can overcome the strength-ductility trade-off in structural materials. Originated from the development of traditional alloys, the intrinsic stacking fault energy…
Bicontinuous nanoporous materials possess remarkable mechanical properties, such as higher specific strength and lower specific modulus compared to fully dense materials combined with low densities and high specific surface areas.…
Large-area ($\sim$cm$^2$) films of vertical heterostructures formed by alternating graphene and transition-metal dichalcogenide(TMD) alloys are obtained by wet chemical routes followed by a thermal treatment at low temperature (300…
A novel medium manganese steel named Novalloy with composition Fe-8.3Mn-3.8Al-1.8Si-0.5C-0.06V-0.05Sn was developed and thermomechanically processed through hot rolling and intercritical annealing. The steel possessed a yield strength of 1…
A systematic study of the compression creep properties of a single-crystalline Co-base superalloy (Co-9Al-7.5W-2Ta) was conducted at 950 {\deg}C, 975 {\deg}C and 1000 {\deg}C to reveal the influence of temperature and the resulting…
High-entropy alloys (HEAs) comprise a compositionally complex class of materials that in certain cases exhibit outstanding mechanical properties. While substantial progress has been made in understanding their phase stability,…
This paper examines the effect of temperature on the structural stability and mechanical properties of 20 layered (10,10) single walled carbon nanotubes (SWCNTs) under tensile loading using an O(N) tight binding molecular dynamics (TBMD)…
The effect of tensile stress applied during cooling of binary glasses on the potential energy states and mechanical properties is investigated using molecular dynamics simulations. We study the three-dimensional binary mixture that was…
In situ straining experiments were performed in a TEM on an equimolar CoCrFeMnNi (Cantor) high entropy alloy at room and cryogenic temperature. Perfect and partial dislocation activity were recorded in both cases. Twinning directly follows…
We measure the stress state in and around a deformation nanotwin in a twinning-induced plasticity (TWIP) steel. Using four-dimensional scanning transmission electron microscopy (4D-STEM), we measure the elastic strain field in a…
The plastic deformation processes that occur in a tensily deformed High Density Polyethylene specimen were studied from full-field strain and strain rate measurements obtained by 3D DIC (Digital Image Correlation).The tensile tests were…