相关论文: Creep deformation of WC hardmetals with iron-based…

We study the creep behavior of a disordered brittle material (concrete) under successive loading steps, using acoustic emission and ultrasonic sensing to track internal damage. The primary creep rate is observed to follow a (Omori-type)…

We numerically investigate the athermal creep deformation of amorphous materials having a wide range of stability. The imposed shear stress serves as the control parameter, allowing us to examine the time-dependent transient response…

Creep is a time-dependent deformation of solids at relatively low stresses, leading to the breakdown with time. Here we propose a simple model for creep failure of disordered solids, in which temperature and stress are controllable. Despite…

Creep tests on heterogeneous materials under subcritical loading typically show a power-law decaying strain rate before failure, with the exponent often considered material-dependent but independent of applied stress. By imposing successive…

Ce$_{2}$$M$Al$_{7}$Ge$_{4}$ ($M=$ Co, Ir, Ni or Pd) are heavy-fermion materials and host a variety of ground states ranging from magnetism to non-Fermi liquid behavior. The Co, Ir, and Ni members of the series undergo magnetic ordering with…

We simulate the stresses induced by temperature changes in a putative hard layer near the surface of comet 67P/Churyumov--Gerasimenko with a thermo-viscoelastic model. Such a layer could be formed by the recondensation or sintering of water…

Chromium thin films deposited on silicon substrates by DC magnetron sputtering were systematically investigated as a function of film thickness, using a DC power of 50 W and a post-deposition annealing temperature of 200 C. Two types of…

This study investigates the substitution of cerium (Ce) with mischmetal (MM) in cast Al-MM alloys, focusing on microstructure, hardness, tensile and compression properties, creep resistance, and coarsening resistance. Al-MM alloys with…

Creep of directionally solidified Sn-3Ag-0.5Cu wt.% (SAC305) samples with near-<110> orientation along the loading direction and different microstructural lengthscale is investigated under constant load tensile testing and at a range of…

We carry out strain-controlled in-situ compression experiments of micron-sized tungsten (W) micropillars in the temperature range 300-900 K, together with simulations of three-dimensional discrete dislocation dynamics (DDD) at the same…

Microscale dynamic testing is vital to the understanding of material behavior at application relevant strain rates. However, despite two decades of intense micromechanics research, the testing of microscale metals has been largely limited…

The reporting and evaluation of creep tests of concrete is complicated by the fact that creep is significant even for the shortest observable load durations. Compared to the strain after 0.1 s load duration, the strain at 2 hour duration is…

Hydrogen (H) content modifies the creep response of Fe-based alloys by altering thermodynamics of point-defects; here we identify the electronic-structure mechanism underlying this effect. Using spin-polarized first-principles calculations…

We examine the competition between the charge-density wave (CDW) instability and the excitonic condensate (EC) in spatially separated layers of electrons and holes. The CDW and the EC order parameters (OPs), described by two different…

Tungsten carbide cobalt hardmetals are commonly used as cutting tools subject to high operation temperature and pressures, where the mechanical performance of the tungsten carbide phase affects the wear and lifetime of the material. In this…

The occurrence of high stress concentrations in reactor components is a still intractable phenomenon encountered in fusion reactor design. We observe and quantitatively model a non-linear high-dose radiation mediated microstructure…

Applying the strong pinning formalism to the mixed state of a type II superconductor, we study the effect of thermal fluctuations (or creep) on the penetration of an ac magnetic field as quantified by the so-called Campbell length…

Fe-Cr binary alloys serve as simplified model systems to study irradiation damage relevant to fusion structural materials. Here, Fe-3%Cr and Fe-5%Cr samples were irradiated with 4 MeV Fe ions under a dose rate of 4x10^5 dpa/s across a…

Magnesium (Mg) and its alloys offer great potential for reducing vehicular mass and energy consumption due to their inherently low densities. Historically, widespread applicability has been limited by low strength properties compared to…

Conventional drop-weight techniques were modified to accommodate low-amplitude force transducer signals from low-strength, cold isostatically pressed 'heavy' composites of polytetrafluoroethylene, aluminum and tungsten. The failure…