相关论文: Microstructure evolution and densification during …
The present work reports the role of different atomic mobility induced localized pore evolution on densification during spark plasma sintering of nanocrystalline W-Mo alloy powder. The shrinkage (or expansion) behavior of cold compacted…
The influence of microstructure on thermoelectricity is increasingly recognized. Approaches for microstructural engineering can hence be exploited to enhance thermoelectric performance, particularly through manipulating crystalline defects,…
Developing nanostructured bulk ceramics is a major challenge when conventional high-temperature sintering is employed for consolidation. In the current investigation, yttria-stabilized zirconia (YSZ) with a composition of ZrO2 - 3 mol% Y2O3…
Nanocrystalline metals are promising materials for wear-resistant applications due to their superior strength and hardness, but prior work has shown that cyclic loading can lead to coarsening. In this study, scratch wear tests were carried…
Nanocrystalline metals with average grain sizes of only a few nanometers have recently been observed to fail through the formation of shear bands. Here, we investigate this phenomenon in nanocrystalline Ni which has had its grain structure…
The development of dispersion of nanoparticles in the W-1%Y$_2$O$_3$ and W-1%La$_2$O$_3$ (wt%) alloys processed by hot isostatic pressing has been investigated using small angle neutron scattering. The mode values of these centers are found…
The mechanisms of fast low-temperature Spark Plasma Sintering (SPS) of W + 10% wt. Ni powders were investigated. The powder compositions were obtained in two methods: (i) by mixing W and Ni powders in a specified ratio (hereinafter referred…
Pulsed Laser Deposition allows to obtain W and W-Ta alloy coatings with different nanostructures, monitored by X-ray diffraction. The correlation between such structures and the elastic properties is investigated for amorphous-like,…
A systematic study of the compression creep properties of a single-crystalline Co-base superalloy (Co-9Al-7.5W-2Ta) was conducted at 950 {\deg}C, 975 {\deg}C and 1000 {\deg}C to reveal the influence of temperature and the resulting…
This work reports the formation of nano- crystalline Al50Cu28Fe22 by high-energy milling. For obtaining the nano-crystalline material, the Al50Cu28Fe22 alloy synthesized through slow cooling of the molten alloy was subjected to ball…
Nanocrystalline bulk materials are desirable for many applications as they combine mechanical strength and specific electronic transport properties. Our bottom up approach starts with tailored nanoparticles. Compaction and thermal treatment…
Microcompression testing is used to probe the uniaxial stress-strain response of a nanocrystalline alloy, with an emphasis on exploring how grain size and grain boundary relaxation state impact the complete flow curve and failure behavior.…
Nanocrystalline materials are well known for their beneficial mechanical and physical properties. However, it is of utmost importance to stabilize the microstructure at elevated temperatures to broaden the window of application e.g. by…
Spark plasma sintering (SPS) of MgAl2O4 powder was investigated at temperatures between 1200 and 1300{\deg}C. A significant grain growth was observed during densification. The densification rate always exhibits at least one strong minimum,…
Understanding grain-boundary mobility during spark plasma sintering can enable microstructure control in high-entropy carbides, yet quantitative grain-growth kinetics remain scarce. In this work, grain growth kinetics and densification…
Monophasic and homogeneous Ni10Zr7 nanocrystalline alloy films were successfully grown at room temperature by co-sputtering in an indigenously developed three-gun DC/RF magnetron sputtering unit. The films could be produced with long-range…
The research results of the microstructure and corrosion resistance of Ti and Ti-Al-V Russian industrial titanium alloys obtained by spark plasma sintering (SPS) are described. Investigations of the microstructure, phase composition,…
A large body of literature within the additive manufacturing (AM) community has focused on successfully creating stable tungsten (W) microstructures due to significant interest in its application for extreme environments. However,…
The effects of ageing at 800 $^\circ$C on the properties of the IRIS alloy (Ti$_{49.9}$Al$_{48}$W$_2$B$_{0.1}$) are studied. The initial microstructure of this alloy densified by Spark Plasma Sintering (SPS) is mainly composed of lamellar…
The thermal decomposition behavior, the microstructural evolution and its influence on the mechanical properties of a supersaturated Cu Co solid solution with ~100 nm average grain size prepared by severe plastic deformation is investigated…