相关论文: Fatigue cracking in gamma titanium aluminide
A novel FFT-based phase-field fracture framework for modelling fatigue crack initiation and propagation at the microscale is presented. A damage driving force is defined based on the stored energy and dislocation density, relating…
The deformation and fatigue crack nucleation mechanisms were studied by means of slip trace analysis and secondary electron microscopy in a textured AZ31B-O Mg alloy subjected to fully-reversed cyclic deformation at two different cyclic…
Advanced g-TiAl based intermetallics Mo-bearing have been developed to obtain the fine-grained microstructure required for superplastic deformation to be used during further processing. In the present work we have studied an alloy of…
In this report, we investigate the effect of low coefficient of thermal expansion (CTE) metals on the operating speed of hafnium-based oxide capacitance. We found that the cooling process of low CTE metals during rapid thermal annealing…
Crack initiation governs high cycle fatigue life and is susceptible to microstructural details. While corresponding microstructure-sensitive models are available, their validation is difficult. We propose a validation framework where a…
There is a long standing technological problem in which a stress dwell during cyclic loading at room temperature in Ti causes a significant fatigue life reduction. It is thought that localised time dependent plasticity in soft grains…
Mechanical stress-induced damage to the articular cartilage can result in fracture imitation or significant tissue degeneration leading to osteoarthritis (OA) compromising joint mobility. Despite the clinical significance, a comprehensive…
Roughness of i-AlPdMn cleaved surfaces are presently analysed. From the atomic scale to 2-3 nm, they are shown to exhibit scaling properties hiding the cluster (0.45 nm) aperiodic structure. These properties are quantitatively similar to…
The thermophysical properties of oxide scale, in the general case, are affected by the variation of the temperature of phase transitions (either magnetic or polymorphic) in its components due to impurities, lattice defects, grain sizes,…
The paper investigates friction and friction heat of the micronscale iron under influences of velocity of the slider and temperature of the substrate by using smoothed particle hydrodynamics simulations. In the velocity range of 10 - 100…
The emerging applications of hydrogels in devices and machines require these soft materials to maintain robustness under cyclic mechanical loads. Whereas hydrogels have been made tough to resist fracture under a single cycle of mechanical…
It is often observed that thermal stress enhances crack propagation in materials, and conversely, crack propagation can contribute to temperature shifts in materials. In this study, we first consider the thermoelasticity model proposed by…
Creep-fatigue interaction in single-crystal nickel superalloys is difficult to predict because the response depends on the combined effects of loading parameters, hold time, temperature, and the underlying deformation mechanisms. This is…
Wire + arc additive manufacture (WAAM) is an attractive method for manufacturing large-scale aerospace components, however the microstructural changes that occur and the effect of interpass rolling are poorly understood. Therefore two…
We characterize the grain boundary (GB) susceptibility to hydrogen-assisted intergranular cracking in pure nickel as a function of coincident site lattice value ($\Sigma$-n), over a wide range of hydrogen concentrations (4 to 14 wppm).…
It was experimentally confirmed that if steel cyclic stress reduces to less than tensile yield stress values, i.e. in case of high-cycle fatigue, the mechanism of fracture changes from dislocation to vacancy one. This conclusion was based…
In this work we propose a stochastic model for estimating the occurrence of crack initiations on the surface of metallic specimens in fatigue problems that can be applied to a general class of geometries. The stochastic model is based on…
In the framework of the suggested in [arxiv:1803.08247 [cond-mat.mtrl-sci]] statistical theory of the equilibrium flow stress, including yield strength, ${\sigma}_y$, of polycrystalline materials under quasi-static (in case of tensile…
Fatigue failure driven by stress gradients associated to casting defects was studied in two cast nickel-based superalloys. The experimental campaign revealed complex damage phenomena linked to spongeous shrinkages, characterized by their…
Neutron scattering measurements on the one-dimensional gapped S=1 antiferromagnet, CsNiCl3, have shown that the excitation corresponding to the Haldane mass gap Delta at low temperatures persists as a resonant feature to high temperatures.…