相关论文: An assessment of the J-integral test for a metalli…
Thick adhesive layers have potential structural application in ship construction for the joining of a composite superstructure to a steel hull. The purpose of this study is to develop a mechanics model for the adhesive fracture of such lap…
The single lap shear test is widely used to measure the strength of dissimilar welds even though such a test brings limited understanding of the intrinsic weld toughness. The present study proposes a numerical finite element (FE) analysis…
The mode I crack tip asymptotic response of a solid characterised by strain gradient plasticity is investigated. It is found that elastic strains dominate plastic strains near the crack tip, and thus the Cauchy stress and the strain state…
Three dimensional calculations of ductile crack growth under mode I plane strain, small scale yielding conditions are carried out using an elastic-viscoplastic constitutive relation for a progres- sively cavitating plastic solid with two…
The accurate measurement of fracture resistance in elastomers is essential for predicting the mechanical limits of soft devices. Usually, this is achieved by performing tearing or peeling experiments on thin-sheet samples. Here, we show…
The J-integral is recognized as a fundamental parameter in fracture mechanics that characterizes the inherent resistance of materials to crack growth. However, the conventional methods to calculate the J-integral, which require knowledge of…
When a crack interacts with material heterogeneities, its front distorts and adopts complex tortuous configurations that are reminiscent of the energy barriers encountered during crack propagation. As such, the study of crack front…
When brittle hydrogels fail, several mechanisms conspire to alter the state of stress near the tip of a crack, and it is challenging to identify which mechanism is dominant. In the fracture of brittle solids, a sufficient far-field stress…
Crack advance from short or long pre-cracks is predicted by the progressive failure of a cohesive zone in a strain gradient, elasto-plastic solid. The presence of strain gradients leads to the existence of an elastic zone at the tip of a…
This paper presents fracture response of alkali-activated slag (AAS) mortars with up to 30% (by volume) of slag being replaced by waste iron powder which contains a significant fraction of elongated particles. The elongated iron particles…
A series of experimental results on the in-plane fracture of a fiber reinforced laminated composite panel is analyzed using the variational multi-scale cohesive method (VMCM). The VMCM results demonstrate the influence of specimen geometry…
Based on spatial-temporal resolved measurements of the stress field at crack tip based on polarized optical microscopy (str-POM), the stress analysis approach to elastomeric fracture uncovers new insights. We show new phenomenology in…
Fatigue crack growth is decisive for the design of thin-walled structures such as fuselage shells of air planes. The cold rolling process, used to produce the aluminium sheets this structure is made of, leads to anisotropic mechanical…
The shear strength of a pre-cracked sandwich layer is predicted, assuming that the layer is linear elastic or elastic-plastic, with yielding characterized by either J2 plasticity theory or by a strip-yield model. The substrates are elastic…
Ultimately, brittle fracture involves breaking atomic bonds. However, we still lack a clear picture of what happens in the highly deformed region around a moving crack tip. Consequently, we still cannot link nano to atomic-scale phenomena…
In this work, the finite elements method (FEM) is used to analyse the growth of fretting cracks. FEM can be favourably used to extract the stress intensity factors in mixed mode, a typical situation for cracks growing in the vicinity of a…
This paper explores the global Mode I fracture energy of a carbon fiber composite subject to a biaxial stress state at a crack tip, specifically in which one stress component is compressive and parallel to the crack. Based on an…
Slow crack propagation in ductile, and in certain brittle materials, appears to take place via the nucleation of voids ahead of the crack tip due to plastic yields, followed by the coalescence of these voids. Post mortem analysis of the…
In this work, distortion gradient plasticity is used to gain insight into material deformation ahead of a crack tip. This also constitutes the first fracture mechanics analysis of gradient plasticity theories adopting Nye's tensor as primal…
We explore the Mode I fracture toughness of a polymer gel containing a semi-infinite, growing crack. First, an expression is derived for the energy release rate within the linearized, small-strain setting. This expression reveals a crack…