相关论文: Rapid one-step synthesis and compaction of high-pe…
We show here for the first time the use of a cold sintering process (CSP) to sinter CoSb3-based thermoelectric materials. CSP at 150 {\deg}C for 90 min under a uniaxial pressure of 750 MPa yields pieces with a relative density of 86 %,…
The recent discovery of n-type Mg$_3$Sb$_2$ thermoelectric has ignited intensive research activities on searching for potential n-type dopants for this material. Using first-principles defect calculations, here we conduct a systematic…
This is the first report on the enhanced thermoelectric (TE) properties of novel Bi2S3-Bi nanocomposites synthesized using a one-step polyol method at different reaction temperatures (TRe) and time. They are well-characterized as…
The mixed ionic-electronic conductor $\beta$-Zn$_4$Sb$_3$ is a cheap and high performing thermoelectric material, but under operating conditions with a temperature gradient and a running current, the material decomposes as Zn readily…
A new flash (ultra-rapid) spark plasma sintering method applicable to various materials systems, regardless of their electrical resistivity, is developed. A number of powders ranging from metals to electrically insulative ceramics have been…
A nanopowder from p-Bi-Sb-Te with particles ~ 10 nm were fabricated by the ball milling using different technological modes. Cold and hot pressing at different conditions and also SPS process were used for consolidation of the powder into a…
Bulk p and n-type bismuth telluride were prepared using spark plasma texturization method. The texture development along the uniaxial load in the 001 direction is confirmed from both x-ray diffraction analysis and Electron Backscattering…
Solid-state precipitation can be used to tailor materials properties, ranging from ferromagnets and catalysts to mechanical strengthening and energy storage. Thermoelectric properties can be modified by precipitation to enhance phonon…
We present the synthesis of D0$_{22}$ Mn$_{3 - \delta}$Ga ($\delta$ = 0, 1) Heusler alloys by Spark Plasma Sintering method. The single phase Mn$_3$Ga (T$_\mathrm{c}$ $\simeq$ 780 K) is synthesized, while Mn$_2$Ga (T$_\mathrm{c}$ $\simeq$…
We report a solution-processed, ligand supported synthesis of 15-20 nm thick Sb(2-x)Bi(x)Te3 nanoplatelets. After complete ligand removal by a facile NH3-based etching procedure, the platelets are spark plasma sintered to a p-type…
Solid-state thermoelectric cooling is expected to be widely used in various cryogenic applications such as local cooling of superconducting devices. At present, however, thermoelectric cooling using p- and n-type Bi2Te3-based materials has…
Potassium tantalate (KTaO$_{3}$) is a promising material for dielectric applications at low temperature. However, dense and single-phase ceramics cannot be obtained by conventional sintering because of the evaporation of potassium that…
Sb-doped Bi2Te3 is known since the 1950s as the best thermoelectric material for near-room temperature operation. Improvements in material performance are expected from nanostructuring procedures. We present a straightforward and fast…
We study the structural and magnetic properties of the MnBi inter-metallic compound. The LTP (Low Temperature Phase) MnBi compound is successfully synthesized in single step by vacuum encapsulation technique and rapid quenching from phase…
Ternary nitride materials hold promise for many optical, electronic, and refractory applications yet their preparation via solid-state synthesis remains challenging. Often, high pressures or reactive gasses are used to manipulate the…
Whether porosity can effectively improve thermoelectric performance is still an open question. Herein we report that thermoelectric performance can be significantly enhanced by creating porosity in n-type Mg3.225Mn0.025Sb1.5Bi0.49Te0.01,…
Thermoelectric (TE) materials can directly convert heat into electrical energy. However, they sustain costly production procedures and batch-to-batch performance variations. Therefore, developing scalable synthetic techniques for…
MgB2 monofilamentary nickel-sheated tapes and wires were fabricated by means of the ex-situ powder-in-tube method using either high-energy ball milled and low temperature synthesized powders. All sample were sintered at 920 C in Ar flow.…
A new route to the sintering of MgB2 has been identified, based on a reactive infiltration of liquid Mg on a powdered B preform. The technique allows to obtain large bulk manufacts in an inexpensive way, without the need of high pressure…
The MgB2 superconductor synthesized in a flowing argon atmosphere using nanometer magnesium powder as the raw materials, denoted as Nano-MgB2, has been studied by the technique of in-situ high temperature resistance measurement (HT-RT…