相关论文: Design Considerations for Low Power Internet Proto…
We focus on designing Peer-to-Peer (P2P) networks that enable efficient communication. Over the last two decades, there has been substantial algorithmic research on distributed protocols for building P2P networks with various desirable…
The upcoming 3GPP global mobile communication standard 6G strives to push the technological limits of radio frequency (RF) communication even further than its predecessors: Sum data rates beyond 100 Gbit/s, RF bandwidths above 1 GHz per…
A large number of papers are now appearing on sixth-generation (6G) wireless systems, covering different aspects, ranging from vision, architecture, applications, and technology breakthroughs. With cellular systems in mind, this paper…
Energy efficiency is a key requirement for the Internet of Things, as many sensors are expected to be completely stand-alone and able to run for years without battery replacement. Data compression aims at saving some energy by reducing the…
Channel coding plays a pivotal role in ensuring reliable communication over wireless channels. With the growing need for ultra-reliable communication in emerging wireless use cases, the significance of channel coding has amplified.…
Admission control schemes and scheduling algorithms are designed to offer QoS services in 802.16/802.16e networks and a number of studies have investigated these issues. But the channel condition and priority of traffic classes are very…
The widespread application of wireless services and dense devices access have triggered huge energy consumption. Because of the environmental and financial considerations, energy-efficient design in wireless networks becomes an inevitable…
Far-field Wireless Power Transfer (WPT) has attracted significant attention in the last decade. Recently, channel-adaptive waveforms have been shown to significantly increase the DC power level at the output of the rectifier. However the…
Low power oriented circuit optimization consists in selecting the best alternative between gate sizing, buffer insertion and logic structure transformation, for satisfying a delay constraint at minimum area cost. In this paper we used a…
Enhancing the energy efficiency of devices stands as one of the key requirements in the fifth-generation (5G) cellular network and its evolutions toward the next generation wireless technology. Specifically, for battery-limited…
Wireless microsensor networks, which have been the topic of intensive research in recent years, are now emerging in industrial applications. An important milestone in this transition has been the release of the IEEE 802.15.4 standard that…
Next-generation wireless communication systems impose much stricter requirements for transmission rate, latency, and reliability. The peak data rate of 6G networks should be no less than 1 Tb/s, which is comparable to existing long-haul…
From generation to generation there are increasing requirements for wireless standards both in terms of spectral and energy efficiency. While up to now the layered wireless transceiver architecture worked allowing for, e.g., separation of…
Radio frequency (RF) wireless power transfer (WPT) is a promising technology for 6G use cases. It enables a massive, yet sustainable deployment of batteryless energy neutral (EN) devices at unprecedented scale. Recent research on 6G is…
Routing Protocol for Low-Power and Lossy Networks (RPL) is an energy-efficient routing solution for IPv6 over Low-Power Wireless Personal Area Networks (6LoWPAN), recommended for resource-constrained devices. While RPL offers significant…
Multiple-input multiple-output (MIMO) communication has led to immense enhancements in data rates and efficient spectrum management. The evolution of MIMO, though, has been accompanied by increased hardware complexity and array sizes,…
Rate adaptation in 802.11 WLANs has received a lot of attention from the research community, with most of the proposals aiming at maximising throughput based on network conditions. Considering energy consumption, an implicit assumption is…
The advancements in microwave power transfer (MPT) over past decades have enabled wireless power transfer over long distances. The latest breakthroughs in wireless communication, namely massive MIMO, small cells and millimeter-wave…
Cost-effective embedded systems necessitate utilizing the single-wire communication protocol for inter-chip communication, thanks to its reduced pin count in comparison to the multi-wire I2C or SPI protocols. However, current single-wire…
This paper presents a comprehensive study on low-complexity waveform, modulation and coding (WMC) designs for the 3rd Generation Partnership Project (3GPP) Ambient Internet of Things (A-IoT). A-IoT is a low-cost, low-power IoT system…