相关论文: Weak value amplification of photon number operator…

An interferometric arrangement is proposed in which the technique of weak value amplification is implemented in order to enlarge the effect of a single photon on the quadratures of a movable mirror of an optical cavity. The photon interacts…

Weak measurements in combination with post-selection can give rise to a striking amplification effect (related to a large "weak value"). We show that this effect can be understood by viewing the initial state of the pointer as the ground…

Most studies for postselected weak measurement in optomechanical system focus on using a single photon as a measured system. However, we find that using weak coherent light instead of a single photon can also amplify the mirror's position…

In this article we present an experimental proposal for the estimation of an optomechanical parameter in the presence of noise. The estimation is based on the technique of weak value amplification which can enlarge the radiation pressure…

In a weak measurement with post-selection, a measurement value, called the weak value, can be amplified beyond the eigenvalues of the observable. However, there are some controversies whether the weak value amplification is practically…

We revisit the scheme of single-photon weak-coupling optomechanics using post-selection, proposed by Pepper, Ghobadi, Jeffrey, Simon and Bouwmeester [Phys. Rev. Lett. 109, 023601 (2012)], by analyzing the exact solution of the dynamical…

To describe the pre- and post-selected quantum ensembles, a complex quantity called the weak value of an operator is used. The weak value is highly controversial due to the fact that it is not bounded by the possible eigenvalues of the…

We present a weak measurement protocol that permits a sensitive estimation of angular rotations based on the concept of weak-value amplification. The shift in the state of a pointer, in both angular position and the conjugate orbital…

Weak measurement with a coherent state pointer and in combination with an orthogonal postselection can lead to a surprising amplification effect, and we give a fire-new physical mechanism about the weak measurement in order to understand…

The weak measurement proposed by Aharonov and his colleagues extracts information of a physical quantity of the system by the post selection as the shifts of the argument of the probe wavefunction. The shift is called the weak value and is…

Most studies for postselected weak measurement focus on using pure Gaussian state as a pointer, which can only give an amplification limit reaching the level of the ground state fluctuation. When the pointer is initialised in a thermal…

In a quantum-noise limited system, weak-value amplification using post-selection normally does not produce more sensitive measurements than standard methods for ideal detectors: the increased weak value is compensated by the reduced power…

The meaning and its possible applications of post-selected weak amplification in optomechanical system is concisely reviewed.

The implementation of weak-value amplification requires the pre- and post-selection of states of a quantum system, followed by the observation of the response of the meter, which interacts weakly with the system. Data acquisition from the…

Weak measurement [1,19] combined with quantum delayed-choice experiment that use quantum beam splitter instead of the beam splitter give rise to a surprising amplification effect, i.e., counterintuitive negative amplification effect. We…

We show the utility of the weak value amplification to observe the quantum interference between two close lying atomic coherent states in a post-selected atomic cat state, produced in a system of $N$ identical two-level atoms weakly…

The application of postselection to a weak quantum measurement leads to the phenomenon of weak values. Expressed in units of the measurement strength, the displacement of a quantum coherent measuring device is ordinarily bounded by the…

We show that weak measurement can be used to "amplify" optical nonlinearities at the single- photon level, such that the effect of one properly post-selected photon on a classical beam may be as large as that of many un-post-selected…

Weak force amplification describes the process of amplifying a faint low-frequency signal by means of an additional high-frequency modulation, which plays a vital role in quantum sensing and high-precision measurement. However, the…

We present a scheme for achieving amplification of the displacement of the mirror in optomechanical cavity using single-photon postselection where the mirror is initially prepared in squeezed coherent state. The amplification depends on the…