相关论文: Thermal analysis and SANS characterisation of hybr…
Zirconium nitride (ZrN) is a refractory material with good mechanical and thermal properties. It is therefore a good candidate for hard surface treatment at high temperature. In this work, we report the growth and characterization of ZrN by…
In Part I of this study, vibration assisted heat treatments of ZBLAN glass revealed irregular crystallization at higher vibration levels, attributed to intermittent loss of thermal contact between the sample and the inner silica ampoule…
A single crystal of lead-zirconate-titanate (PZT), composition Pb(Zr0.80Ti0.20)O3, was studied by polarized-Raman scattering as a function of temperature. Raman spectra reveal that the local structure deviates from the average structure in…
The NaNO$_{2}$ nanocomposite ferroelectric material in porous glass was studied by neutron diffraction. For the first time the details of the crystal structure including positions and anisotropic thermal parameters were determined for the…
Room and high temperature mechanical properties of reactive magnetron sputtered TaSiN coatings were measured using nanoindentation (between 25C and 500C). Fracture toughness was also evaluated at a similar temperature range using the…
The effect of increasing temperature on the structural stability and interactions of two kinds of Al/Zr (Al(1%wtSi)/Zr and Al(Pure)/Zr) multilayer mirrors are investigated. All Al/Zr multilayers annealed from 200^{\circ}C to 500^{\circ}C,…
Materials that exhibit zero thermal expansion have numerous applications, ranging from everyday ceramic hobs to telescope mirrors to devices in optics and micromechanics. These materials include glass ceramics containing crystal phases with…
Whether porosity can effectively improve thermoelectric performance is still an open question. Herein we report that thermoelectric performance can be significantly enhanced by creating porosity in n-type Mg3.225Mn0.025Sb1.5Bi0.49Te0.01,…
Zirconia (ZrO2) has emerged as a promising technical ceramic, both as high temperature structural material and thermal barrier coating material, etc. The traditional synthesis of ZrO2 with spark plasma sintering (SPS) usually requires a…
A first-principles-derived approach is used to study structural, piezoelectric and dielectric properties of Pb(Zr_{1-x}Ti_{x})O_{3} (PZT) solid solutions near the morphotropic phase boundary at low temperature. Three ferroelectric phases…
Degradation of mechanical properties of zirconia polycrystals is hardly discussed in terms of solution-precipitation grain-boundary sliding due to experimental controversies over imaging of intergranular amorphous phases at high and room…
The oxidation behavior of W-Zr thin-film metallic glasses (TFMGs) with 32, 48 and 61 at.% Zr, prepared by dc magnetron co-sputtering, was comprehensively studied after annealing in synthetic air. The study focuses on the effect of the…
Rubber compounds for pressure sealing application typically have inferior dimensional stability with temperature fluctuations compared with their steel counterparts. This effect may result in seal leakage failures when subjected to…
The effects of thermal treatments on metallic glass nanolaminates (NLs), with a composition of Zr$_{24}$Cu$_{76}$ and Zr$_{61}$Cu$_{39}$ and a bilayer period of 50 nm, were explored to control their mechanical properties through…
December 1991 legislation in France has spurred research on enhanced separation and conditioning or transmutation of long-lived radionuclides from high level radioactive wastes (HLW). In this field, we have studied zirconolite-based…
Synchrotron X-ray diffraction patterns were measured and analyzed for a polycrystalline sample of the room-temperature ferromagnet Sr3.12Er0.88Co4O10.5 from 300 to 650 K, from which two structural phase transitions were found to occur…
In this work cotton and polyester fabric were coated with silica nano particles using pad-dry-cure method. The prepared composite fabrics were analyzed in terms of change in their thermal degradation properties. The oxidative degradation…
Magnesium alloys are emerging as promising alternatives to traditional orthopedic implant materials thanks to their biodegradability, biocompatibility, and impressive mechanical characteristics. However, their rapid in-vivo degradation…
The influence of Zr additions (in the form of ZrH2 particles) on the microstructure and mechanical properties of IN718 Ni-based superalloy manufactured by selective laser melting was explored. Fully dense alloys could be obtained by careful…
La$_{0.67}$Sr$_{0.33}$Mn$_{1-x}$Ti$_x$O$_{3}$ ($0 \le x \le 0.20$) polycrystalline materials are prepared by employing lower annealing temperature compared to the temperatures reported for the materials of the same composition. The…