相关论文: Step-index optical fibre drawn from 3D printed pre…

In modern particle physics experiments wavelength-shifting and scintillating fibres based on plastic polymers are used for tracking and calorimetry. In this review the role of photon trapping efficiencies, transmission functions and signal…

Hollow core antiresonant fibers offer new possibilities in the near infrared and visible spectral range. I show here that the great flexibility of this technology can allow the design and fabrication of hollow core optical fibers with an…

We identify a route towards achieving a negative index of refraction at optical frequencies based on coupling between plasmonic waveguides that support backwards waves. We show how modal symmetry can be exploited in metal-dielectric…

The design of a complex phase mask (CPM) for inscribing aperiodic filters in fibers is presented. The complex structure of the mask surface relief consists of discrete aperiodic phase-steps at periodic intervals. We show that the…

A wavelength-tunable Optical Fiber Tweezer (OFT) based on a Graded Index Multimode Fiber (GIMF) with a flat endface is proposed. It is shown that the design can support a trapping position which is far from the tip of the GIMF compared with…

We have developed a novel integrated platform for liquid photonics based on liquid core optical fiber (LCOF). The platform is created by fusion splicing liquid core optical fiber to standard single-mode optical fiber making it fully…

Optical fibers are the basis for applications that have grown considerably in recent years (telecommunications, sensors, fiber lasers, etc). Despite undeniable successes, it is necessary to develop new generations of amplifying optical…

A detailed investigation of the nonlinear multimodal interference in a short graded-index multimode optical fiber is presented. The analysis is performed for a specific device geometry, where the light is coupled in and out of the multimode…

Dermal interstitial fluid (ISF) is a rich source of biomarkers (e.g., glucose) that can be used for continuous health monitoring with wearable sensors. Hollow microneedle devices are a promising solution to extract ISF on demand by…

We proposed the method of the optical fiber modal decomposition of the radiation propagating in a multimode optical fiber with a step like refractive index profile. The field distribution at the output end of the fiber was used. The method…

The performance of a scintillating fiber detector prototype for tracking under high rate conditions is investigated. A spatial resolution of about100 micron is aimed for the detector. Further demands are low occupancy and radiation hardness…

The resolution of far-field optical microscopes, which rely on propagating optical modes, is widely believed to be limited because of diffraction to a value on the order of a half-wavelength $\lambda /2$ of the light used. Although…

A preselection-free fiber-optic weak measurement sensing framework is proposed and experimentally verified in this paper. In view of the limitation that fiber-optic weak measurement require specific preselection, this scheme innovates…

We design and fabricate ultra-low-loss tapered optical fibers (TOFs) with minimal lengths. We first optimize variations of the torch scan length using the flame-brush method for fabricating TOFs with taper angles that satisfy the…

Optical fibres have already played a huge part in ground based astronomical instrumentation, however, with the revolution in photonics currently taking place new fibre technologies and integrated optical devices are likely to have a…

As a new group of advanced 2D layered materials, bismuth oxyhalides, i.e., BiOX (X = Cl, Br, I), have recently become of great interest. In this work, we characterize the third-order optical nonlinearities of BiOBr, an important member of…

We report on a novel and efficient source of polarization squeezing using a single pass through an optical fiber. Simply passing this Kerr squeezed beam through a carefully aligned lambda/2 waveplate and splitting it on a polarization beam…

Nowadays is very common to find headlines in the media where it is stated that 3D printing is a technology called to change our lives in the near future. For many authors, we are living in times of a third industrial revolution. Howerver,…

We describe an optomechanical device consisting of a fiber-based optical cavity containing a silicon nitiride membrane. In comparison with typical free-space cavities, the fiber-cavity's small mode size (10 {\mu}m waist, 80 {\mu}m length)…

A general-purpose all-fiber spectrometer is demonstrated to overcome the trade-off between spectral resolution and bandwidth. By integrating a wavelength division multiplexer with five multimode optical fibers, we have achieved 100 nm…