相关论文: Micromechanics-Based Simulations of Compressive an…
We demonstrate the ability of a stabilized finite element method, inspired by the weighted Nitsche approach, to alleviate spurious traction oscillations at interlaminar interfaces in multi-ply multi-directional composite laminates. In…
Wet granular materials in a quasi-static steady state shear flow have been studied with discrete particle simulations. Macroscopic quantities, consistent with the conservation laws of continuum theory, are obtained by time averaging and…
Differential shrinkage in particulate quasi-brittle materials causes microcracking which reduces durability in these materials by increasing their mass transport properties. A hydro-mechanical three-dimensional periodic network approach was…
Over the past few decades, the phase-field method for fracture has seen widespread appeal due to the many benefits associated with its ability to regularize a sharp crack geometry. Along the way, several different models for including the…
We study the high-velocity regime mode-I fracture instability when small microbranches start to appear near the main crack, using large scale simulations. Some of the features of those microbranches have been reproduced qualitatively in…
Under inhomogeneous flow, dense suspensions exhibit complex behaviour that violates the conventional homogenous rheology. Specifically, one finds flowing regions with a macroscopic friction coefficient below the yielding criterion, and…
The standard approach to compressive sampling considers recovering an unknown deterministic signal with certain known structure, and designing the sub-sampling pattern and recovery algorithm based on the known structure. This approach…
This research investigates the simultaneous effect of in-plane and transverse loads in reinforced concrete shells. The infinitesimal shell element is divided into layers (with triaxial behavior) that are analyzed according to the smeared…
When a hole is introduced into an elastic material, it will usually act to reduce the overall mechanical stiffness. A general ambition is to investigate whether a stiff shell around the hole can act to maintain the overall mechanical…
This paper focuses on the development of the atomistic framework for determining the lower scale mechanical parameters of single components of a metal matrix composite for final application to a micromechanical damage model. Here, the…
Hard-magnetic soft materials (HMSMs) are particulate composites that consist of a soft matrix embedded with particles of high remnant magnetic induction. Since the application of an external magnetic flux induces a body couple in HMSMs, the…
Eshelby's theory is the foundation of composite mechanics, allowing calculation of the effective elastic moduli of composites from a knowledge of their microstructure. However it ignores interfacial stress and only applies to very dilute…
The original results of experimental investigations concerning the reduction of the seismic vulnerability of masonry vaults through Composite Reinforced Mortar CRM are presented in the paper. The transversal performances of full scale,…
Prevailing machine-learned interatomic potential (MLIP) uncertainty-quantification methods rely on ensembles of independently trained backbones. These methods scale unfavorably with foundation-scale MLIPs, and their member-disagreement…
The mechanical properties of metal matrix fiber-reinforced composites depend on many aspects of their structure in a complicated way. In this paper, we propose a \emph{minimalistic} approach to study interface debonding, matrix cracking,…
Commensurable twisted bilayers can drastically change the magnetic properties of chromium trihalide layered compounds, which opens novel opportunities for tuning magnetic states through layer rotations. Here, we introduce a mathematical…
The discrete modeling of a large class of mechanical structures can be based on a stick-and-spring concept. We here present a stick-and-spring theory with potential application to the statics and the dynamics of such nanostructures as…
We study experimentally the fracture mechanisms of a model cohesive granular medium consisting of glass beads held together by solidified polymer bridges. The elastic response of this material can be controlled by changing the cross-linking…
A numerical model able to simulate solid-state constrained sintering is presented. The model couples an existing kinetic Monte Carlo (kMC) model for free sintering with a finite element model (FEM) for calculating stresses on a…
We analyze the consolidation of freshly deposited cohesive and non-cohesive sediment by means of particle-resolved direct Navier-Stokes simulations based on the Immersed Boundary Method. The computational model is parameterized by material…