相关论文: Thin Flexible Lithium Ion Battery Featuring Graphi…
We report the lithium plating associated capacity loss during fast charging of compressively loaded lithium-ion batteries (LIBs). The charging and discharging of LIB under compressive loading during service may affect the cell performance…
The solid-state electrolyte is critical for achieving next-generation high energy density and high-safety batteries. Solid polymer electrolytes (SPEs) possess great potential for commercial application owing to their compatibility with the…
Energy efficient, safe and reliable Li-ion batteries (LIBs) are required for a wide range of applications. Charging capabilities of thick electrodes still holding their stored high-energy is a most desirable characteristic in future…
We report on the efficient photodetection (PD) properties of graphene based p-i-n photodetector, where all the three layers are either single or multilayer graphene sheets. We report the bandwidth and responsivity performance of the device.…
In the quest to increase battery performance, nanostructuring battery electrodes gives access to architectures with electrical conductivity and solid-state diffusion regimes not accessible with traditional electrodes based on aggregated…
In this study, novel flexible micro-scale humidity sensors were directly fabricated in graphene oxide (GO) and polyimide (PI) using ion beam writing without any further modifications, and then successfully tested in an atmospheric chamber.…
Existence of van der Waals gaps renders two-dimensional (2D) materials ideal passages of lithium for being used as anode materials. However, the requirement of good conductivity significantly limits the choice of 2D candidates. So far only…
Black phosphorous is a layered material having a high capacity of 2596 mAh/g as a battery electrode, however it suffers from cracking due to high volume expansion during lithiation. These cracks causes loss of electrical contact in the…
Porous and flexible actuating materials are important in the development of smart systems. We report here a facile method to prepare scalable, flexible actuating porous membranes based on a poly(ionic liquid)-modified tissue paper. The…
Solid-ion conductors (SICs) comprising non-ionic plastic crystals and lithium salts often require compositing with polymers to render them processable for use in solid-state lithium-metal batteries. Here, we show that polymer-doped plastic…
Next-generation high-efficiency Li-ion batteries require an electrolyte that is both safe and thermally stable. A possible choice for high performance all-solid-state Li-ion batteries is a liquid crystal, which possesses properties…
The prospects of phosphorene as an anode material for high performance Li-ion battery was systematically investigated from the first principle calculations and experimental measurements. The diffusion energy barriers of a Li atom moving…
The development of silicon anodes to replace conventional graphite in efforts to increase energy densities of lithium-ion batteries has been largely impeded by poor interfacial stability against liquid electrolytes. Here, stable operation…
A solar cell design using the combination of titanium dioxide and graphite as active photon absorbing materials were proposed. The titanium dioxide absorbs photons of nearly ultraviolet wavelengths to produce electron hole pairs, while…
Distributions of potential and lithium content inside lithium ion batteries highly affects their performance and durability. An increased heterogeneity of the lithium distribution is expected in thick electrodes with high energy densities…
The development of multifunctional solid-state materials is key to advancing lithium-ion batteries with enhanced safety and simplified architectures. Here, we report a scalable, highly efficient (near $100\%$), solvent-free mechanochemical…
This study presents a materials-design framework for low-voltage pressure-sensitive electroadhesives based on ion-containing bottlebrush polymers that combine the on-demand reversibility of traditional electroadhesives with the tunable…
Photo-rechargeable (solar) battery can be considered as an energy harvesting cum storage system, where it can charge the conventional metal-ion battery using light instead of electricity, without having other parasitic reactions. Here we…
Two-dimensional (2D) materials have received considerable attention as possible electrodes in Li-ion batteries (LIBs), although a deeper understanding of the Li adsorption behavior as well as broad screening of the materials space is still…
A novel WS2-graphite dual-ion battery (DIB) is developed by combining together a conventional graphite cathode and high-capacity few-layer WS2 flakes anode. The WS2 flakes are produced by exploiting wet-jet milling (WJM) exfoliation, which…