相关论文: Investigations on the energy balance in TDCB tests
In this work we present the design of a new test geometry inspired by the Tapered Double Cantilever Beam (TDCB) specimen that is shown to provide an improved characterization of the fracture properties of brittle solids. First, we show that…
In this work, the mode I fracture toughness of dissimilar metal-composite adhesive joints is experimentally investigated using the double cantilever beam (DCB) test. The particular joint under study is resulted by the adhesive joining of a…
The dissipation of energy in dynamic force microscopy is usually described in terms of an adhesion hysteresis mechanism. This mechanism should become less efficient with increasing temperature. To verify this prediction we have measured…
Thick adhesive layers have potential structural application in ship construction for the joining of a composite superstructure to a steel hull. The purpose of this study is to develop a mechanics model for the adhesive fracture of such lap…
This work aims to identify common challenges in the preparation of the blister test devices designed for measurement of energy release rate for brittle thin films and to propose easy-to-implement solutions accordingly. To this end, we…
We study the onset of delamination blisters in a growing elastic sheet adhered to a flat stiff substrate. When the ends of the sheet are kept fixed, its growth arouses residual stresses that lead to delamination. This instability can be…
We perform traction experiments on viscous liquids highly confined between parallel plates, a geometry known as the probe-tack test in the adhesion community. Direct observation during the experiment coupled to force measurement shows the…
Dynamic mode decomposition method is deployed to investigate the heat transfer mechanism in a compressible turbulent shear layer and shockwave. To this end, highly resolved Large Eddy Simulations are performed to explore the effect of wall…
Adhesive interactions between elastic structures such as graphene sheets, carbon nanotubes, and microtubules have been shown to exhibit hysteresis due to irrecoverable energy loss associated with bond breakage, even in static…
The dispersion coefficient of the constant phase element (CPE) is typically treated as an empirical fitting parameter in the analysis of impedance spectroscopy data, with no clear physical meaning. Here we seek to establish a energy-based…
We have designed a new experimental setup able to investigate fracture of soft materials at small scales. At high crack velocity, where energy is mostly dissipated through viscoelastic processes, we observe an increasingly large high strain…
The paper addresses the problem of a Mode III interfacial crack advancing quasi-statically in a heterogeneous composite material, that is a two-phase material containing elastic inclusions, both soft and stiff, and defects, such as…
The micromixing time of impinging thin liquid sheets depends upon the energy dissipation rate. The kinetic energy released by the impingement has been previously studied and was found to be a function of the coefficient of restitution of…
This paper explores the global Mode I fracture energy of a carbon fiber composite subject to a biaxial stress state at a crack tip, specifically in which one stress component is compressive and parallel to the crack. Based on an…
We carry out uniaxial continuous and step stretching of various crosslinked polymer networks to demonstrate how characteristics of rupture (from continuous stretching) and delayed rupture (from step stretching) can be used to probe the…
The accurate measurement of fracture resistance in elastomers is essential for predicting the mechanical limits of soft devices. Usually, this is achieved by performing tearing or peeling experiments on thin-sheet samples. Here, we show…
The shear strength of a pre-cracked sandwich layer is predicted, assuming that the layer is linear elastic or elastic-plastic, with yielding characterized by either J2 plasticity theory or by a strip-yield model. The substrates are elastic…
I study the influence of temperature and the crack-tip velocity of the bond breaking at the crack tip in rubber-like materials. The bond breaking is considered as a stress-aided thermally activated process and result in an effective crack…
The current paper presents an experimental study of the energy budget of a two-dimensional internal wave attractor in a trapezoidal domain filled with uniformly stratified fluid. The injected energy flux and the dissipation rate are…
A general procedure to investigate the elastic response and calculate the elastic constants of stressed and unstressed materials through continuum field modeling, particularly the phase field crystal (PFC) models, is presented. It is found…