相关论文: Work hardening behavior in a steel with multiple T…

Understanding the mechanism of martensitic transformation is of great importance in developing advanced high strength steels, especially TRansformation-Induced Plasticity (TRIP) steels. The TRIP effect leads to enhanced work-hardening rate,…

A medium Mn steel of composition Fe-4.8Mn-2.8Al-1.5Si-0.51C (wt.\%) was processed to obtain two different microstructures representing two different approaches in the hot rolling mill, resulting in equiaxed vs. a mixed equiaxed and lamellar…

Carbon is a well known austenite stabiliser and can be used to alter the stacking fault energy and stability against martensitic transformation in medium Mn steels, producing a range of deformation mechanisms such as the Transformation…

Partitioning at phase boundaries of complex steels is important for their properties. We present atom probe tomography results across martensite / austenite interfaces in a precipitation-hardened maraging TRIP steel (12.2 Mn, 1.9 Ni, 0.6…

A novel medium manganese steel named Novalloy with composition Fe-8.3Mn-3.8Al-1.8Si-0.5C-0.06V-0.05Sn was developed and thermomechanically processed through hot rolling and intercritical annealing. The steel possessed a yield strength of 1…

A novel medium Mn steel of composition Fe-12Mn-4.8Al-2Si-0.32C-0.3V was manufactured with 1.09 GPa yield strength, 1.26 GPa tensile strength and 54% elongation. The thermomechanical process route was designed to be industrially translatable…

High-manganese twinning-induced plasticity (TWIP) steels exhibit high strain hardening, high tensile strength, and high ductility, which make them attractive for structural applications. At low tensile strain rates, TWIP steels are prone to…

A Twinning Induced Plasticity (TWIP) steel with a nominal composition of Fe-16.4Mn-0.9C-0.5Si-0.05Nb-0.05V was deformed to an engineering strain of 6\%. The strain around the deformation twins were mapped using the 4D-STEM technique. Strain…

The article focuses on the effect of alloying and microstructure on formability of advanced high strength steels (AHSSs) processed via quenching and partitioning (Q&P). Three different Q&P steels with different combination of alloying…

My scientific activities aim at understand and predict the mechanical behaviour of steels, from fundamental mechanisms to macroscopic deformation. This manuscript is dedicated to the TWIP effect (TWinning Induced Plasticity) of high…

The onset of plasticity in quenched martensitic microstructures is characterized by a low initial yield stress followed by an extremely strong initial hardening response, and then a sudden hardening saturation. Literature attributes this…

Martensite damage in Dual-Phase (DP) steel has been studied extensively, yet, the exact deformation mechanisms that trigger or inhibit damage initiation remain mostly unexplored. Whereas generally assumed to be hard and brittle, lath…

In situ neutron diffraction of the uniaxial tension test was used to study the effect of the surrounding matrix microstructure on the mechanical stability of retained austenite in high-carbon bearing steels. Comparing the samples with…

This work explains the occurrence of transformation-induced plasticity via stress-assisted martensite, when designing ultrafine-grained duplex steels. It is found that, when the austenite is reduced to a fine scale of about 300 nm, the…

A new $\beta$-metastable Ti-alloy is designed with the aim to obtain a TWIP alloy but positioned at the limit between the TRIP/TWIP and the TWIP dominated regime. The designed alloy exhibits a large ductility combined with an elevated and…

This work presents a detailed experimental-numerical analysis of a low-carbon dual-phase steel microstructure, revealing evidence of significant anisotropic plastic deformation in lath martensite. A careful determination of the habit plane…

A novel concept of varying the strain hardening rate of a medium Mn steel with 8 wt\% Mn by varying the duration of the intercritical anneal after hot rolling was explored. It was found that the stability of the austenite phase showed an…

We study experimentally the intermittent progress of the mechanically induced martensitic transformation in a Cu-Al-Be single crystal through a full-field measurement technique: the grid method. We utilize an in- house, specially designed…

The mechanical response of third-generation advanced high-strength steels is governed by phase transformations at the nanoscale, yet the coupled evolution of chemistry and crystallography remains poorly resolved. Here we apply a correlative…

Aiming at increasing the yield strength of transformation and twinning induced plasticity (TRIP and TWIP) titanium alloys, a dual-phase $\alpha$/$\beta$ alloy is designed and studied. The composition Ti 7Cr 1.5Sn (wt.%) is proposed, based…