相关论文: Formation of Microcrystalline Structure in Large-S…
The alpha/beta interface in Ti-6Al-2Sn-4Zr-6Mo (Ti-6246) is investigated via centre of symmetry analysis, both as-grown and after 10% cold work. Semi-coherent interface steps are observed at a spacing of 4.5 +/-1.13 atoms in the as-grown…
This paper presents a review on the superplastic forming of Ti-6Al-4V alloy, which has been used to manufacture parts of complex shapes and geometries. This paper outlines the major work carried out on this front in the past three decades.…
Additive manufacturing of Ti-6Al-4V alloy via laser powder-bed fusion leads to non-equilibrium $\alpha'$ martensitic microstructures, with high strength but poor ductility and toughness. These properties may be modified by heat treatments,…
Nanostructured Fe40Ni40P14B6 alloys ingots of diameter 3~5 mm could be synthesised by a metastable liquid state spinodal decomposition method. The molten Fe40Ni40P14B6 alloy was purified by means of the fluxing technique and thus a large…
The {\alpha}+\b{eta} titanium alloy (Ti6Al4V) has been successfully joined using rotary friction welding. To investigate the influence of post weld heat treatments on the microstructure and mechanical properties of the welds, the weld…
The microstructural features and high-temperature oxidation resistance of hybrid (TiC+TiB) networks reinforced Ti-6Al-4V composites were investigated after fabricated with reaction hot pressing technique. The inhomogeneous distribution of…
Fretting wear is a surface degradation process caused by oscillatory motion and contact slipping. During gross slip, high local stresses and plastic deformation in the surface and subsurface can lead to the creation of a nanosized grained…
A hot salt corrosion (HSC) test was performed on the fine-grained titanium alpha-alloy Ti-2.5Al-2.6Zr (Russian industrial alloy PT-7M). The ultrafine-grained (UFG) microstructure in the titanium alpha-alloy was formed via cold Rotary…
Microstructural features and mechanical properties of an Al-Mg-Si alloy processed by high-pressure torsion have been investigated using transmission electron microscopy, X-ray diffraction, three-dimensional atom probe, tensile tests and…
High-pressure X-ray diffraction experiments were performed on Ti-Al-V alloys to investigate the effect of composition on structural stability, focusing on Ti-3Al-2.5V and comparing with pure Titanium and Ti-6Al-4V. Measurements using…
Superplastic behavior of ultrafine-grained (UFG) Al-6Mg-0.12Sc-0.10Zr-0.1X alloys, where X = Yb (Alloy #1-Yb), Er (Alloy #2-Er), and Hf (Alloy #3-Hf), has been studied. The total content of Sc, Zr, Yb, Er, Hf in the alloys was 0.32 wt.%…
Aiming to simulate the radiation damage effect on a dual alpha+beta phase Ti-6Al-4V alloy utilized as high-intensity accelerator beam window material, a series of irradiation experiments were conducted with a 2.8 MeV-Fe^2+ ion beam in…
The ability to create complex geometries with tailored material properties has brought interest in using additive manufacturing (AM) techniques in various industrial applications. However, the complex relationship between AM process…
Advanced g-TiAl based intermetallics Mo-bearing have been developed to obtain the fine-grained microstructure required for superplastic deformation to be used during further processing. In the present work we have studied an alloy of…
A high-intensity proton beam exposure with 181 MeV energy has been conducted at Brookhaven Linac Isotope Producer facility on various material specimens for accelerator targetry applications, including titanium alloys as a beam window…
The mimicry of crystalline microstructure at meso-scale creates a new class of architected materials, termed meta-crystals, and offers effective ways to significantly improve the toughness and eliminate the post-yield collapse of…
Components manufactured via Wire + Arc Additive Manufacturing are usually characterised by large columnar grains. This can be mitigated by introducing in-process cold-rolling; in fact, the associated local plastic deformation leads to a…
The research results of the microstructure and corrosion resistance of Ti and Ti-Al-V Russian industrial titanium alloys obtained by spark plasma sintering (SPS) are described. Investigations of the microstructure, phase composition,…
Samples of $\alpha$-SiC have been sintered with liquid phase (LPS) to 1950 $^\circ$C, in atmosphere of argon and processing times between 1 and 7 hours. Using scanning electron microscopy (SEM) the microstructure of the samples has been…
Three novel precipitation strengthened bcc alloys which exhibit a smooth microstructural gradient with composition have been fabricated in bulk form by induction casting. All three alloys are comprised of a mixture of disordered A2-(Fe, Cr)…