相关论文: Submicrometer Pattern Fabrication by Intensificati…
Slippage of Newtonian liquids in the presence of a solid substrate is a newly found phenomenon the origin of which is still under debate. In this paper, we present a new analysis method to extract the slip length. Enhancing the slip of…
Dewetting of thin liquid films is monitored in situ by atomic force microscopy, results are compared with simulations. The experimental setting is mimicked as close as possible using the experimental parameters including the effective…
The dewetting dynamics of an ultrathin film is studied in the presence of evaporation - or reaction - of adatoms on the substrate. KMC simulations are in good agreement with an analytical model with diffusion, rim facetting, and substrate…
We report an ultrafast, parallel and beyond-the-master micro-patterning technique for ultrathin (30 nm-400 nm) non-absorbing polymer films by diffraction of a laser light through a two dimensional periodic aperture. The redistribution of…
We have observed nanopattern formation with robust and controllable spatial ordering by laser-induced dewetting in nanoscopic metal films. Pattern evolution in Co film of thickness 1\leq h\leq8 nm on SiO_{2} was achieved under multiple…
The dewetting dynamics of ultrathin polymer films, e.g. in the model system of polystyrene on a polydimethylsiloxane-covered substrate, exhibits interesting behavior like a fast decay of the dewetting velocity and a maximum in the width of…
We report on the delamination of thin ($\approx \mu$m) hydrogel films grafted to silicon substrates under the action of swelling stresses. Poly(dimetylacrylamide) (PDMA) films are synthesized by simultaneously cross-linking and grafting…
The synthesis and application of deuterated polystyrene (dps) films is discussed. Ultracold neutron storage properties and the Fermi potential of dps films is measured with the result that Tstore=700 +/- 200 sec for dps in the bottle used…
Dewetting of thin metal films is one of the most widespread method for functional plasmonic nanostructures fabrication. However, simple thermal-induced dewetting does not allow to control degree of nanostructures order without additional…
In large area micro hot embossing, the process temperature plays a critical role to both the local fidelity of microstructure formation and global uniformity. The significance of low temperature hot embossing is to improve global flatness…
We have investigated the reduction of the glass transition temperature, $T_g$, for thin supported films of particularly small molecular weight ($M_W$ = 2 kg/mol) polystyrene, and found good agreement with earlier studies on larger…
We investigate the effect of short chains on slip of highly entangled polystyrenes (PS) during thin film dewetting from non-wetting fluorinated surfaces. Binary and ternary mixtures were prepared from monodisperse PS with weight average…
The sticky fluids found in pitcher plant leaf vessels can leave fractal-like filaments behind when dewetting from a substrate. To understand the origin of these filaments, we investigate the dynamics of a retreating thin-film of aqueous…
The dewetting of thin Pt films on different surfaces is investigated as a means to provide the patterning for the top-down fabrication of GaN nanowire ensembles. The transformation from a thin film to an ensemble of nanoislands upon…
Density of the polyacrylamide ultrathin films has been studied using X-ray reflectivity technique. Two sources (one powder and another aqueous solution) of polyacrylamide were used to prepare spin coated films on silicon substrate. Light…
The film thickness dependence of crystal growth is investigated for isotactic polystyrene (it-PS) in thin films, the thickness of which is from 20nm down to 4nm. The single crystals of it-PS grown at 180 in the ultrathin films show the…
We revisit the fundamental problem of liquid-liquid dewetting and perform a detailed comparison of theoretical predictions based on thin-film models with experimental measurements obtained by atomic force microscopy (AFM). Specifically, we…
Physical vapor deposition (PVD) is widely used in manufacturing ultra-thin layers of amorphous organic solids. Here, we demonstrate that these films exhibit a sharp transition from glassy solid to liquid-like behavior with thickness below…
The objective of this work is to study the role of shear on the rupture of ultrathin polymer films. To do so, a finite-difference numerical scheme for the resolution of the thin film equation was set up taking into account capillary and van…
Understanding the mechanical properties of metals at extreme conditions is essential for the advancement of miniaturized technologies. As dimensions decrease, materials will experience higher strain rates at the same applied velocities.…