相关论文: Decomposition process in a FeAuPd alloy nanostruct…
A FePd alloy was nanostructured by severe plastic deformation following two different routes: ordered and disordered states were processed by high pressure torsion (HPT). A grain size in a range of 50 to 150 nm is obtained in both cases.…
A complex study of aging kinetics for both coarse-grained and nanostructured by severe plastic deformation Cu -- 2 wt% Be alloy is reported. It is shown that aging of a coarse-grained alloy leads to continuous formation of nanosized CuBe…
This work gives insights into processing and characterisation of bulk nanocrystalline FeCr materials. The investigated FeCr alloys, consisting of 30, 50 and 70 at.% ferromagnetic Fe and remaining anti-ferromagnetic Cr, are processed by arc…
The thermal decomposition behavior, the microstructural evolution and its influence on the mechanical properties of a supersaturated Cu Co solid solution with ~100 nm average grain size prepared by severe plastic deformation is investigated…
A Cu-Fe nanocomposite containing 50 nm thick iron filaments dispersed in a copper matrix was processed by torsion under high pressure at various strain rates and temperatures. The resulting nanostructures were characterized by transmission…
The processing of binary alloys consisting of ferromagnetic Fe and antiferromagnetic Cr by severe plastic deformation (SPD) with different chemical compositions has been investigated. Although the phase diagram exhibits a large gap in the…
Ultrafine-grained aluminum alloys offer interesting multifunctional properties with a combination of high strength, low electrical resistivity, and low density. However, due to thermally induced grain coarsening, they typically suffer from…
Initial powder mixtures of Cu, Fe and Co are exposed to severe plastic deformation by high-pressure torsion to prepare solid solutions. A broad range of compositions is investigated, whereas this study aims at the synthesis of soft magnetic…
A Cu-Cr composite was processed by severe plastic deformation to investigate the role of interphase boundaries on the grain size reduction mechanisms. The as-deformed material exhibits a grain size of only 20nm. This gives rise to a…
Grain boundary segregations were investigated by Atom Probe Tomography in an Al-Mg alloy, a carbon steel and Armco\trademark Fe processed by severe plastic deformation (SPD). In the non-deformed state, the GBs of the aluminium alloy are Mg…
A filamentary composite elaborated by cold drawing was processed by High Pressure Torsion (HPT). The nanostructure resulting from this severe plastic deformation (SPD) was investigated thanks to scanning electron microscopy, transmission…
Nanostructured Fe40Ni40P14B6 alloys ingots of diameter 3~5 mm could be synthesised by a metastable liquid state spinodal decomposition method. The molten Fe40Ni40P14B6 alloy was purified by means of the fluxing technique and thus a large…
Nanocrystalline metals, i.e. metals with grain sizes from 5 to 50 nm, display technologically interesting properties, such as dramatically increased hardness, increasing with decreasing grain size. Due to the small grain size, direct…
Nanostructures have the immense potential to supplant the traditional metallic structure as they show enhanced mechanical properties through strain hardening. In this paper, the effect of grain size on the hardening mechanism of Al-Cu…
We studied solid solution effects on the mechanical properties of nanocrystalline (NC) $\mathrm{Pd}_{\mathrm{100-x}} \mathrm{Au}_{\mathrm{x}}$ alloys ($0 \leq \mathrm{x} < 50 \mathrm{at.\%}$) at the low end of the nanoscale. Concentration…
Strengthening by grain refinement via the Hall-Petch mechanism and softening by nanograin formation via the inverse Hall-Petch mechanism have been the subject of argument for decades, particularly for ultrafine-grained materials. In this…
A series of Co_xCu_{100-x} (x = 0, 40...75, 100) layers with thicknesses in-between 13 nm and 55 nm were prepared on silicon substrates using cross-beam pulsed laser deposition. Wide-angle X-ray diffraction (WAXRD), transmission electron…
Hot rolled commercial metastable austenitic steel 321 with strongly elongated thin delta-ferrite particles in its microstructure was the object of investigations. Ultrafine-grained (UFG) microstructure in steel 321 was formed by Equal…
Twenty-one distinct AlxCoCrFeNi alloys were rapidly prepared by laser alloying an equiatomic CoCrFeNi substrate with Al powder to create an alloy library ranging x=0.15-1.32. Variations in crystal structure, microstructure and mechanical…
This work reports the formation of nano- crystalline Al50Cu28Fe22 by high-energy milling. For obtaining the nano-crystalline material, the Al50Cu28Fe22 alloy synthesized through slow cooling of the molten alloy was subjected to ball…