相关论文: Design And Fabrication of Condenser Microphone Usi…
We present the design and performance of a 2x2 prototype array of corrugated feed-horns in W-band. The module is fabricated using a so-called "platelet" technique by milling Aluminum plates. This technique is suitable for low-cost and…
Most microphones operate by detecting the sound-pressure induced motion of a membrane. In contrast, here we introduce a microphone that operates by monitoring the sound-pressure-induced modulation of the compressibility of air. By driving a…
The effect of tensile stress on magnetoimpedance (MI) in CoMnSiB amorphous wires at microwave frequencies (0.5-3 GHz) is investigated both experimentally and theoretically. In the presence of the dc bias magnetic field of the order of the…
The design of an improved microstrip antenna operating in the 28 GHz frequency spectrum is the main goal of this work. The design used a Roger RT 5880 LZ substrate with a thickness and permittivity of 0.762mm and 1.96, respectively. The…
Metasurfaces composed of subwavelength unit cells usually require a large number of unit cells which leads to complicated design and optimization. Aggressive discretization in a metasurface can significantly reduce the number of unit cells…
Dielectric losses are one of the key factors limiting the coherence of superconducting qubits. The impact of materials and fabrication steps on dielectric losses can be evaluated using coplanar waveguide (CPW) microwave resonators. Here, we…
Development of novel radiation-absorbent materials and devices for millimetre and submillimetre astronomy instruments is a research area of high interest, and with substantial engineering challenges. Alongside low-profile structure and…
We present an open-access dataset of over 8000 acoustic impulse from 160 microphones spread across the body and affixed to wearable accessories. The data can be used to evaluate audio capture and array processing systems using wearable…
The microwave properties of a crystalline sapphire dielectric whispering gallery mode resonator have been measured at very low excitation strength (E/hf=1) and low temperatures (T = 30 mK). The measurements were sensitive enough to observe…
We investigate the acoustical properties of uncompressed and compressed open-celled aluminum metal foams fabricated using a directional solidification foaming process. We compressed the fabricated foams using a hydraulic press to different…
The measurement of the close-to-the-carrier noise of rf and microwave devices is a relevant issue in time and frequency metrology and in some fields of electronics, physics and optics. While phase noise is the main concern, amplitude noise…
We have tuned the whispering gallery modes of a fused silica microresonator over nearly 1 nm at 800 nm, i.e. over 0.5 FSR or 10^6 linewidths of the resonator. This has been achieved by a new method based on the stretching of a two-stem…
A finite-element model is presented for numerical simulation in three dimensions of acoustophoresis of suspended microparticles in a microchannel embedded in a polymer chip and driven by an attached piezoelectric transducer at MHz…
Microwave energy can be advantageously used for materials processing as it provides high heating rates and homogeneous temperature field distribution. These features are partly due to the large microwave penetration depth into dielectric…
We present measurements at millikelvin temperatures of the microwave-frequency acoustic properties of a crystalline silicon nanobeam cavity incorporating a phononic bandgap clamping structure for acoustic confinement. Utilizing pulsed laser…
We have experimentally demonstrated an on-chip all-silk fibroin whispering gallery mode microresonator by using a simple molding and solution-casting technique. The quality factors of the fabricated silk protein microresonators are up to…
In large area micro hot embossing, the process temperature plays a critical role to both the local fidelity of microstructure formation and global uniformity. The significance of low temperature hot embossing is to improve global flatness…
Nano-engineering crystalline materials can be used to tailor their thermal properties. By adding new nanoscale phonon scattering centers and controlling their size, one can effectively decrease the phonon mean free path and hence the…
We design extremely-thin acoustic metasurfaces, providing a versatile platform for the manipulation of reflected pressure fields, that are constructed from mass loads and stretched membranes fixed to a periodic rigid framework. These…
A theoretical study is performed to analyze the directional response of different types of microphone array designs. 1-D (linear) and 2-D (planar) microphone array types are considered, and the delay and sum beamforming and conventional…