Related papers: Present Status of VEPP-5 Control System
The control system of the VEPP-4 facility was designed more than fifteen years ago and based on the home-developed CAMAC-embedded minicomputers Odrenok [1]. Five years ago, all computers were connected via Ethernet network. This step…
The VEPP-4 control system was designed almost 20 years ago as CAMAC-based distributed control system. Today the main peculiarity of the upgraded VEPP-4 control system is the employment of obsolete CAMAC-embedded 24-bit Odrenok computers in…
We will use EPICS toolkit [1] to build a prototype for upgrading BEPC control system. The purposes are for the following three aspects: (1) Setup a network based distributed control system with EPICS. (2) Study some front-end control…
Most of the devices in the SLAC control system are accessed via interface modules in ~450 CAMAC crates. Low-cost controllers in these crates communicate via a SLAC-proprietary bit-serial protocol with 77 satellite control computers…
The control system of the 1.5 MeV FEL injector is built on the base of ported EPICS. It uses low-cost hardware: personal computers with the processor Intel x86 and CAMAC equipment produced by our institute. At present time, the distributed…
Modern PC workstations often provide more CPU power than required for most control applications. On the other hand, the screen space is always in short supply. One possible solution is to use more PCs, but in fact we need only more screens,…
Louisiana State University Center for Advanced Microstructures and Devices (CAMD) began a control system upgrade project in early 1997. At the time, the storage ring was controlled by a VAX/VMS system, primarily using CAMAC for I/O. The…
As an accelerator control system survives over several years, it is often the case that new subsystems are introduced into the original control system. The control system for the KEK electron/positron injector-linac has been using Unix…
We present the current status of APENet, our custom 3-dimensional interconnect architecture for PC clusters environment. We report some micro-benchmarks on our recent large installation as well as new developments on the software and…
The Sonix is the main control software for the IBR-2 instruments. This is a modular configurable and flexible system created using the Varman (real time database) and the X11/OS9 graphical package in the OS-9 environment. In the last few…
A pipeline CAMAC controller with PC/104-Plus single board computer has been developed. The architecture of the pipeline CAMAC controller is completely different from that of traditional CAMAC controller. The pipeline CAMAC controller…
The growing complexity of real-time control algorithms with increasing performance demands, along with the shift to 2.5D technology, drive the need for scalable controllers to manage chiplets' coupled operation in 2.5D systems-in-package.…
This paper addresses frequency regulation under operational constraints in interconnected power systems with high penetration of inverter-based renewable generation. A two-layer control architecture is proposed that combines optimized droop…
he ESRF control system is in the process of being modernised. The present contrsystem is based on VME, 10 MHz Ethernet, OS9, Solaris, HP-UX, NFS/RPC, Motif and C. The new control system will be based on compact PCI, 100 MHz Ethernet, Linux,…
The SRS is a 2GeV synchrotron light source with 14 beamlines serving approximately 34 experimental stations. Control of the major elements of the beamlines (vacuum pumps, gauges, valves and radiation stops) is the responsibility of the main…
Volt/var control (VVC) of smart PV inverter is becoming one of the most popular solutions to address the voltage challenges associated with high PV penetration. This work focuses on the local droop VVC recommended by the grid integration…
Vortex, a newly proposed open-source GPGPU platform based on the RISC-V ISA, offers a valid alternative for GPGPU research over the broadly-used modeling platforms based on commercial GPUs. Similarly to the push originating from the RISC-V…
Efficient operation of a submillimeter interferometer requires remote (preferably automated) control of mechanically tuned local oscillators, phase-lock loops, mixers, optics, calibration vanes and cryostats. The present control system for…
In the last decade, we have witnessed exponential growth in the complexity of control systems for safety-critical applications (automotive, robots, industrial automation) and their transition to heterogeneous mixed-criticality systems…
Real-time control systems often require dedicated hardware and software, including real-time operating systems, while many systems are available for off-line computing, mainly based on standard system units (PCs), standard network…