Related papers: 3D Printed Alumina as a Millimeter-Wave Optical El…
The ATLAS experiment at the LHC will replace its current inner tracker system for the HL-LHC era. 3D silicon pixel sensors are being considered as radiation-hard candidates for the innermost layers of the new fully silicon-based tracking…
In this letter, we present the direct loss tangent measurement of a high-resistivity intrinsic (100) silicon wafer in the temperature range from ~ 70 mK to 1 K, approaching the quantum regime. The measurement was performed using a technique…
This paper proposes an experiment to easily detect radiative heat transfer in the microwave range. Following an idea given by Pendry more than a decade ago [1], we show that a 3D array of tungsten 2micron radius wires with a 1 cm period…
Silicon-nitride-on-insulator photonic circuits have seen tremendous advances in many applications, such as on-chip frequency combs, Lidar, telecommunications, and spectroscopy. So far, the best film quality has been achieved with low…
Aluminum gallium arsenide (AlGaAs) and related III-V semiconductors have excellent optoelectronic properties. They also possess strong material nonlinearity as well as high refractive indices. In view of these properties, AlGaAs is a…
Laser cutting of semiconductor wafers and transparent dielectrics has become a dominant process in manufacturing industries, encompassing a wide range of applications from flat display panels to microelectronic chips. Limited by the…
The 4--8 GHz FR1(C) and 7--24 GHz upper mid-band FR3 spectrum are promising new 6G spectrum allocations being considered by the International Telecommunications Union (ITU) and major governments around the world. There is an urgent need to…
We demonstrate aqueous refractive index sensing with 15 to 30 {\mu}m diameter silicon nitride microdisk resonators to detect small concentrations of Li salt. A dimpled-tapered fiber is used to couple 780 nm visible light to the microdisks,…
A thorough analysis of the refractive index of eleven 1-alkyl-3-methylimidazolium-based ionic liquids with three different anions, tetrafluoroborate bis(trifluoromethylsulfonyl)imide, and trifluoromethanesulfonate, is reported. Refractive…
A wedge-shaped structure made of split-ring resonators (SRR) and wires is numerically simulated to evaluate its refraction behavior. Four frequency bands, namely, the stop band, left-handed band, ultralow-index band, and positive-index…
This paper presents 73 GHz wideband outdoor foliage and ground reflection measurements. Propagation measurements were made with a 400 Megachip-per-second sliding correlator channel sounder, with rotatable 27 dBi (7 degrees half- power…
Scandium aluminum nitride (ScAlN) has recently emerged as an attractive material for integrated photonics due to its favorable nonlinear optical properties and compatibility with CMOS fabrication. Despite the promising and versatile…
Small unmanned aircraft systems (sUAS) have allowed for thousands of aerial images to be captured at a moments notice. The simplicity and relative low cost of flying a sUAS has provided remote sensing practitioners, both commercial and…
The increasing need of restoring high-resolution Hyper-Spectral (HS) images is determining a growing reliance on Computer Vision-based processing to enhance the clarity of the image content. HS images can, in fact, suffer from degradation…
The investigation of the mechanical loss of different silicon flexures in a temperature region from 5 to 300 K is presented. The flexures have been prepared by different fabrication techniques. A lowest mechanical loss of $3\times10^{-8}$…
A broadband two-layer anti-reflection (AR) coating was developed for use on a sapphire half-wave plate (HWP) and an alumina infrared (IR) filter for cosmic microwave background (CMB) polarimetry. Measuring tiny CMB B-mode signals requires…
The microscale integration of mid- and longwave-infrared photonics could enable the development of fieldable, robust chemical sensors, as well as highly efficient infrared frequency converters. However, such technology would be defined by…
Metallic gratings were fabricated using high energy laser interference lithography with a frequency tripled Nd:YAG nanosecond laser. The grating structures were first recorded in a photosensitive layer and afterwards transferred to an Au…
We report the first observation of a superconducting transition in a 3D printed, metallised-plastic device. A cylindrical cavity is 3D printed from a photosensitive polymer resin and then a 20 $\mu$m layer of tin deposited. A resonant TE…
Applications such as augmented and virtual reality (AR/VR), optical atomic clocks, and quantum computing require photonic integration of (near-)visible laser sources to enable commercialization at scale. The heterogeneous integration of…