Related papers: Microstructural and material property changes in s…
We investigated the effect of nano-structuring by high-pressure torsion (HPT) on the irradiation performance of Eurofer-97. Material was deformed to shear strains from 0 to ~230, and then exposed to Fe$^{3+}$ irradiation doses of 0.01 and…
Understanding the evolution of dislocation structures during plastic deformation is critical for predicting the mechanical performance of metallic materials. In this work, we applied in situ scanning electron microscopy/electron backscatter…
The microstructure and mechanical properties of materials saturate to steady states after severe plastic deformation (SPD). Despite the well-known effect of temperature on the steady-state microstructure, there is no general agreement on…
Understanding the mechanisms of plasticity in structural steels is essential for the operation of next-generation fusion reactors. Elemental composition, particularly the amount of Cr present, and irradiation can have separate and…
The deformation behavior of nearly fully pearlitic, bainitic and martensitic steels during severe plastic deformation is summarized in this paper. Despite their significantly different yield stresses and their microstructures, their…
In this study, the effect of ferrite grain size on the mechanical properties and dislocation behavior of dual-phase (DP) steel is investigated using dislocation-based crystal plasticity finite element analysis. DP steel, composed of a soft…
Nickel carbon nanotube composites with varying amounts of carbon nanotubes are deformed by high pressure torsion at different deformation temperatures to high strains, where no further refinement of the Nickel matrix microstructure is…
Ceramics are typically brittle at ambient conditions due to their covalent or ionic bonding and limited dislocation activities. While plasticity, and occasionally superplasticity, can be achieved in ceramics at high temperatures through…
Bulk nanocrystalline materials of small and medium ferromagnetic content were produced using severe plastic deformation by high-pressure torsion at roomtemperature. Giant magnetoresistive behavior was found for as deformed materials, which…
Heavy plastic shear deformation at relatively low homologous temperatures is called high-pressure torsion (HPT) deformation, which is one method of severe plastic deformation (SPD). The aim of the paper is to give an overview of a new…
A variety of severe plastic deformation (SPD) techniques have been developed to process materials to high strains and impart microstructural refinement. High pressure torsion (HPT) is one technique that imparts inhomogeneous strain to…
The combined strengthening effects of grain refinement and high precipitated volume fraction (~6at.%) on the mechanical properties of FeSiTi alloy subjected to SPD processing prior to aging treatment were investigated by atom probe…
Plasticity in body-centred cubic (BCC) metals, including dislocation interactions at grain boundaries, is much less understood than in face-centred cubic (FCC) metals. At low temperatures additional resistance to dislocation motion due to…
The dislocation microstructure developing during plastic deformation strongly influences the stress-strain properties of crystalline materials. The novel method of high resolution electron backscatter diffraction (HR-EBSD) offers a new…
Mixtures of Fe and Cu powders are cold-compacted and subsequently deformed with severe plastic deformation by high-pressure torsion, leading to bulk samples. The dilution of Fe in the Cu matrix is investigated with SQUID-magnetometry,…
Metals are important structural materials for transport and the built environment. Low carbon steels can fail through strain localisation due to the role of interstitial solute atoms (such as carbon and nitrogen) interacting with mobile…
The High Nitrogen Martensitic Stainless Steel (HNMS) was subjected to three different austenitizing cycles of 1050$^\circ$C, 1075$^\circ$C and 1100$^\circ$C followed by subzero treatment at -70$^\circ$C. The fraction of retained austenite…
Irradiation-induced ductility loss is a major concern facing structural steels in next-generation nuclear reactors. Currently, the mechanisms for this are unclear but crucial to address for the design of reactor components. Here, the…
A Cu-Cr composite was processed by severe plastic deformation to investigate the role of interphase boundaries on the grain size reduction mechanisms. The as-deformed material exhibits a grain size of only 20nm. This gives rise to a…
A FePd alloy was nanostructured by severe plastic deformation following two different routes: ordered and disordered states were processed by high pressure torsion (HPT). A grain size in a range of 50 to 150 nm is obtained in both cases.…