Related papers: Creep-fatigue interactions in a polycrystalline st…
Creep-fatigue interaction in single-crystal nickel superalloys is difficult to predict because the response depends on the combined effects of loading parameters, hold time, temperature, and the underlying deformation mechanisms. This is…
There is a long standing technological problem in which a stress dwell during cyclic loading at room temperature in Ti causes a significant fatigue life reduction. It is thought that localised time dependent plasticity in soft grains…
For corrosion-induced cracking in reinforced concrete, naturally occurring corrosion rates are so low that rust accumulates often over tens of years near the surface of the reinforcement bars before sufficient pressure in the surrounding…
A new phenomenological model of cyclic creep is proposed which is suitable for applications involving finite creep deformations of the material. The model accounts for the the effect of the transient increase of the creep strain rate upon…
Creep tests on heterogeneous materials under subcritical loading typically show a power-law decaying strain rate before failure, with the exponent often considered material-dependent but independent of applied stress. By imposing successive…
The creep behaviour and microstructural evolution of a Sn-3Ag-0.5Cu wt.% sample with a columnar microstructure have been investigated through in-situ creep testing under constant stress of 30 MPa at 298 K. This is important, as 298 K is…
Long-term operation of nuclear steam generators can result in the occurrence of clogging, a deposition phenomenon that may increase the risk of mechanical and vibration loadings on tube bundles and internal structures as well as potentially…
Crystal-level strain rate sensitivity and temperature sensitivity are investigated in Zircaloy-4 using combined of bending creep test, digital image correlation, electron backscatter detection and thermo-mechanical tensile tests with…
Crystalline materials exhibit an hysteresis behaviour when deformed cyclically. The origins of this tension-compression asymmetry have been fully understood only recently as being caused by an asymmetry in the junction strength and a…
Creep of directionally solidified Sn-3Ag-0.5Cu wt.% (SAC305) samples with near-<110> orientation along the loading direction and different microstructural lengthscale is investigated under constant load tensile testing and at a range of…
Previous studies demonstrate that grain-boundary sliding could accelerate creep rate and give rise to large internal stresses that can lead to damage development, e.g. formation of wedge cracks. The present study provides more insight into…
Creep is a time-dependent deformation of solids at relatively low stresses, leading to the breakdown with time. Here we propose a simple model for creep failure of disordered solids, in which temperature and stress are controllable. Despite…
A microstructure-based model that accounts for the effect of grain size has been developed to study the effect of grain size on the fatigue life of Inconel 718 alloys. The fatigue behavior of two alloys with different grain size was…
Creep failure of hierarchical materials is investigated by simulation of beam network models. Such models are idealizations of hierarchical fibrous materials where bundles of load-carrying fibers are held together by multi-level…
The damage mechanisms and load redistribution of high strength TC17 titanium alloy/unidirectional SiC fibre composite (fibre diameter = 100 $\mu$m) under high temperature (350 {\deg}C) fatigue cycling have been investigated in situ using…
Early age behaviour of concrete is based on complex multi-physical and multiscale phenomena. The predication of both cracking risk and residual stresses in hardened concrete structures is still a challenging task. We propose in this paper a…
Predicting the mechanical failure of parts in service requires understanding their deformation behavior, and associated dynamic microstructural evolution up to the near-atomic scale. Solutes are known to interact with defects generated by…
We numerically investigate the athermal creep deformation of amorphous materials having a wide range of stability. The imposed shear stress serves as the control parameter, allowing us to examine the time-dependent transient response…
Creep deformation in shale rocks is an important factor in many applications, such as the sustainability of geostructures, wellbore stability, evaluation of land subsidence, CO2 storage, toxic waste containment, and hydraulic fracturing.…
Long-term creep (i.e., deformation under sustained load) is a significant material response that needs to be accounted for in concrete structural design. However, the nature and origin of creep remains poorly understood, and controversial.…