Related papers: Processing of nanostructured bulk Fe-Cr alloys by …
The deformation behavior of nearly fully pearlitic, bainitic and martensitic steels during severe plastic deformation is summarized in this paper. Despite their significantly different yield stresses and their microstructures, their…
A complex study of aging kinetics for both coarse-grained and nanostructured by severe plastic deformation Cu -- 2 wt% Be alloy is reported. It is shown that aging of a coarse-grained alloy leads to continuous formation of nanosized CuBe…
This study addresses microstructure selection mechanisms in rapid solidification, specifically targeting the transition from cellular/dendritic to planar interface morphologies under conditions relevant to additive manufacturing. We use a…
Ferromagnetic (Fe or Fe20Ni80) and antiferromagnetic (NiO) phases were deformed by high pressure torsion, a severe plastic deformation technique, to manufacture bulk sized nanocomposites and demonstrate an exchange bias, which has been…
We consider the process of precipitation in binary alloys in the presence of mechanical deformation. It is commonly observed that mechanical deformation prior to or during precipitation leads to microstructure with excess defects, which…
Severe plastic deformation changes the microstructure and properties of steels, which may be favourable for their use in structural components of nuclear reactors. In this study, high-pressure torsion (HPT) was used to refine the grain…
In this study, severe plastic deformation by high pressure torsion is used as a fabrication method for nanocrystalline magnetic CuCo alloys in bulk quantities. By subsequent isothermal annealing, phase separation of the supersaturated solid…
A redistribution of Cr atoms related to a phase decomposition (PD) caused by an isothermal annealing at 415 C in a 15.15 at%Cr Fe-Cr alloy was studied in an ex-situ way by the conversion electrons M\"ossbauer spectroscopy. Analysis of the…
Grain size engineering, particularly reducing grain size into the nanocrystalline regime, offers a promising pathway to further improve the strength-to-weight ratio of Al alloys. Unfortunately, the fabrication of nanocrystalline metals…
In this work, we have designed obtained a novel multiferroic nanocomposite using the high-pressure torsion (HPT) method. The crystal structure, phase composition, morphology, ferromagnetic (FM) and ferroelectric (FE) properties of the…
Superplastic behavior of ultrafine-grained (UFG) Al-6Mg-0.12Sc-0.10Zr-0.1X alloys, where X = Yb (Alloy #1-Yb), Er (Alloy #2-Er), and Hf (Alloy #3-Hf), has been studied. The total content of Sc, Zr, Yb, Er, Hf in the alloys was 0.32 wt.%…
The properties of bulk nanostructured materials are often controlled by atomic scale features like segregation along defects or composition gradients. Here we discuss about the complimentary use of TEM and APT to obtain a full description…
Nano-scale eutectics, such as rapid solidified Al-Si, exhibit enhanced yield strength and strain hardening but plasticity is limited by cracking of the hard phase (Si). Mechanisms that may suppress cracking and enable plastic co-deformation…
Here we use large-scale molecular dynamics (MD) simulations of the high-rate deformation of nanocrystalline tantalum to investigate the processes associated with plastic deformation for strains up to 100%. We use initial atomic…
Bulk composites using powder blends of Mn and Bi with equal atomic ratios are consolidated and severely deformed by high-pressure torsion (HPT). Subsequent annealing treatments lead to the formation of the ferromagnetic and rare-earth free…
Bulk metallic samples were synthesized from different binary powder mixtures consisting of elemental Cu, Co, and Fe using severe plastic deformation. Small particles of the ferromagnetic phase originate in the conductive Cu phase, either by…
Nickel carbon nanotube composites with varying amounts of carbon nanotubes are deformed by high pressure torsion at different deformation temperatures to high strains, where no further refinement of the Nickel matrix microstructure is…
Friction Stir Processing is a relatively new technique which has been developed for microstructural modification of metallic materials through intense, localized plastic deformation. The current research work deals with the development of…
Twenty-one distinct AlxCoCrFeNi alloys were rapidly prepared by laser alloying an equiatomic CoCrFeNi substrate with Al powder to create an alloy library ranging x=0.15-1.32. Variations in crystal structure, microstructure and mechanical…
A variety of severe plastic deformation (SPD) techniques have been developed to process materials to high strains and impart microstructural refinement. High pressure torsion (HPT) is one technique that imparts inhomogeneous strain to…