Related papers: Novel high efficiency quadruple junction solar cel…
A high photon to electricity conversion efficiency of 47.2082% was achieved by a novel combination of In0.51Ga0.49P, GaAs, In0.24Ga0.76As and In0.19Ga0.81Sb subcell layers in a quadruple junction solar cell design. The electronic bandgap of…
Multijunction solar cell design is guided by both the theoretical optimal bandgap combination as well as the realistic limitations to materials with these bandgaps. For instance, triple-junction III-V multijunction solar cells commonly use…
We simulated photovoltaic characteristics of single heterojunction solar cell with Cu2ZnSnS4 and Cu2ZnSnSe4 absorber layer numerically using one dimensional solar cell capacitance simulator (SCAPS-1D). n-CdS/ZnO double buffer layer is used…
The fundamental efficiency limit of a single bandgap solar cell is about 31% at one sun with a bandgap of about Eg = 1.35 eV (1), determined by the trade-off of maximising current with a smaller bandgap and voltage with a larger bandgap.…
Power-conversion efficiency is a critical factor for the wider adoption of solar-cell modules. Thin-film solar cells are cheap and easy to manufacture, but their efficiencies are low compared to crystalline-silicon solar cells and need to…
Organic-inorganic halide perovskite materials have emerged as attractive alternatives to conventional solar cell building blocks. Their high light absorption coefficients and long diffusion lengths suggest high power conversion efficiencies…
Tandem solar cells can better harness the energy of the solar spectrum. Chalcopyrite solar cells have drawn attention, being the only highly efficient devices with bandgap around 1.0 eV, suitable for bottom cells. In the quest for better…
We demonstrate four and two-terminal perovskite-perovskite tandem solar cells with ideally matched bandgaps. We develop an infrared absorbing 1.2eV bandgap perovskite, $FA_{0.75}Cs_{0.25}Sn_{0.5}Pb_{0.5}I_3$, that can deliver 14.8 %…
We present a multiscale approach for modeling an intermediate-band solar cell based on a GaAs-GaAlAs quantum dot superlattice of cubic symmetry. Our framework combines high-accuracy theoretical calculations of the superlattice band…
In this paper we carried out theoretical study of the general issues related to the efficiency of SiC:H/a-Si:H single- and multi-junction tandem solar cells. Implementation of numerical simulations by the use of AMPS-1D program of…
This paper proposes an efficient three-layered p-GaAs/p-CIGS/n-CdS (PPN), a unique solar cell architecture. Copper indium gallium selenide (CIGS)-based solar cells exhibit substantial performance than the ones utilizing cadmium sulfide…
Intermediate band solar cells (IBSCs) pursue the increase in efficiency by absorbing below-bandgap energy photons while preserving the output voltage. Experimental IBSCs based on quantum dots have already demonstrated that both…
Single junction Si solar cells dominate photovoltaics but are close to their efficiency limits. This paper presents ideal limiting efficiencies for tandem and triple junction multijunction solar cells subject only to the constraint of the…
Photovoltaic materials are recognized for their potential as sustainable energy sources that enable the conversion between light and electrical energy. However, solar cells have been unable to surpass the theoretical limit of 32%, known as…
Harnessing low energy photons is of paramount importance for multi-junction high efficiency solar cells as well as for thermo-photovoltaic applications. However, semiconductor absorbers with bandgap lower than 0.8 eV have been limited to…
Cu based ternary chalcogenides are gathering attention for sustainable energy applications due to their reduced complexity compared to quaternary alternatives. We used drift diffusion modeling to evaluate the feasibility of photovoltaics…
The Shockley and Queisser limit, a well-known efficiency limit for a solar cell, is based on unrealistic physical assumptions and its maximum limit is seriously overestimated. To understand the power loss mechanisms of record-efficiency…
In this article, we demonstrate the design and simulation of a highly-efficient n-CdS/p-CIGS/p+-CGS dual heterojunction solar cell. The simulation was performed using SCAPS-1D software with reported experimental physical parameters. The…
Compared to traditional pn-junction photovoltaics, hot carrier solar cells offer potentially higher efficiency by extracting work from the kinetic energy of photogenerated "hot carriers" before they cool to the lattice temperature. Hot…
In this paper we study CdS/CdTe solar cells by means of AMPS-1D software. First we study the effect of thickness of semiconductor layers on the output parameters of the CdS/CdTe solar cell, such as density of short-circuit current, open…