Related papers: Statistical Extraction of Useful Concrete Creep Da…
Motivated by recent experiments studying the creep and breakup of a protein gel under stress, we introduce a simple mesoscopic model for the irreversible failure of gels and fibrous materials, and demonstrate it to capture much of the…
The early strength evolution of self-consolidating concrete (SCC) is studied by a set of non-standard mechanical tests for compressive, tensile, shear and bending failure. The results are applicable in an industrial environment for process…
When materials are loaded below their short-term strength over extended periods, a slow time-dependent process known as creep deformation takes place. During creep deformation, the structural properties of a material evolve as a function of…
The slow motion of a crack line is studied via an experiment in which sheets of paper are split into two halves in a ``peel-in-nip'' (PIN) geometry under a constant load, in creep. The velocity-force relation is exponential. The dynamics of…
Sloped terrains tend to creep downward over time, even when their slope is below the nominal angle of repose. This behavior can result from periodic variations in environmental conditions, such as daily or seasonal fluctuations in…
The solidification theory has been accepted as a thermodynamically sound way to describe the creep reduction due to deposition of hydrated material in the pores of concrete. The concept of self-equilibrated nanoscale microprestress has been…
We compare and synthesize the results of two microrheological experiments on the cytoskeleton of single cells. In the first one, the creep function J(t) of a cell stretched between two glass plates is measured after applying a constant…
Co-base superalloys are considered as promising high temperature materials besides the well-established Ni-base superalloys. However, Ni appears to be an indispensable alloying element also in Co-base superalloys. To address the influence…
The aim of the paper is to derive the exact analytical expressions for torsion and bending creep of rods with the Norton-Bailey, Garofalo and Naumenko-Altenbach-Gorash constitutive models. These simple constitutive models, for example, the…
Iron is a candidate to replace cobalt in WC hardmetals, due to its lower cost and toxicity. A WC-FeCr hardmetal was compression tested at 900-1200 {\deg}C. Particular attention is paid to the steady-state creep rates and stress-exponents…
The stress analysis of pressurized circumferential pipe weldments under steady state creep is considered. The creep response of the material is governed by Norton's law. Numerical and analytical solutions are obtained by means of…
We numerically investigate the athermal creep deformation of amorphous materials having a wide range of stability. The imposed shear stress serves as the control parameter, allowing us to examine the time-dependent transient response…
We report two-dimensional discrete dislocation dynamics simulations of combined dislocation glide and climb leading to `power-law' creep in a model aluminum crystal. The approach fully accounts for matter transport due to vacancy diffusion…
An introductory review to short-time critical dynamics is given. From the scaling relation valid already in the early stage of the evolution of a system at or near the critical point, one derives power law behaviour for various quantities.…
We report on the dynamics of a model frictional system submitted to minute external perturbations. The system consists of a chain of sliders connected through elastic springs that rest on an incline. By introducing cyclic expansions and…
Yield stress materials fail when the imposed stress crosses a critical threshold. A well-known dynamical response to the applied stress is the phenomenon of creep where the cumulative deformation grows sublinearly with time, prior to…
The creep behavior of an amorphous poly(etherimide) (PEI) polymer is investigated in the vicinity of its glass transition in a weakly non linear regime where the acceleration of the creep response is driven by local configurational…
The destabilization of emulsions is important for many applications but remains incompletely understood. We perform squeeze flow measurements on oil-in-water emulsions, finding that the spontaneous destabilization of emulsions is generally…
Polymer-based plastics exhibit time-dependent deformation under constant stress, known as creep, which can lead to rupture or static fatigue. A common misconception is that materials under tolerable static loads remain unaffected over time.…
A new phenomenological model of cyclic creep is proposed which is suitable for applications involving finite creep deformations of the material. The model accounts for the the effect of the transient increase of the creep strain rate upon…