Related papers: Electrometer calibration with sub-part-per-million…
Atomic force microscopy (AFM) is an analytical surface characterization tool which can reveal a sample's topography with high spatial resolution while simultaneously probing tip-sample interactions. Local measurement of chemical properties…
A class of Actively Calibrated Line Mounted Capacitive Voltage Transducers (LMCVT) are introduced as a viable line mountable instrumentation option for deploying large numbers of voltage transducers onto the medium and high voltage systems.…
The Low Frequency Instrument (LFI) on-board the ESA Planck satellite carries eleven radiometer subsystems, called Radiometer Chain Assemblies (RCAs), each composed of a pair of pseudo-correlation receivers. We describe the on-ground…
An ellipsometer is a vital precision tool used for measuring optical parameters with wide applications in many fields, including accurate measurements in film thickness, optical constants, structural profiles, etc. However, the precise…
We implemented a low noise current preamplifier for the readout of resistive bolometers. We tested the apparatus on thermometer resistances ranging from 10 Ohm to 500 Mohm. The use of current preamplifier overcomes constraints introduced by…
A silicon electron pump operating at the temperature of liquid helium has demonstrated repeatable operation with sub-ppm accuracy. The pump current, approximately 168 pA, is measured by three laboratories, and the measurements agree with…
Integrators are fundamental instruments to recover differential signals from magnetic probes in Experimental Advanced Superconducting Tokamak (EAST) experiments. A kind of difference integrator is introduced which has the same structure as…
The high frequency primary power standard is univocally realized by means of a coaxial microcalorimeter, at least up to 40 GHz. The coaxial microcalorimeter is a broadband measurement system adjusted for effec-tive efficiency measurement of…
The inductive charging of electric vehicles requires specific measurement and calibration systems. In fact, the measurement of power on board involves DC signals, which are superimposed to a significant AC ripple up to or over 150 kHz,…
Within the domain of optical frequency comb systems operating in the mid-infrared, extensive exploration has been undertaken regarding critical parameters such as stabilization, coherence, or spectral tunability. Despite this, certain…
This paper proposes a low-power and low-noise instrumentation amplifier (IA) tailored for bioimpedance sensing applications. The design originates from a gain-boosted flipped voltage follower (FVF) transconductance (TC) stage and integrates…
A temperature controlled 1 {\Omega}-10 k{\Omega} standard Resistors transportable setup was developed at National Institute of Metrological Research, (INRIM) for the calibration and adjustment of multifunction electrical instruments. The…
Two special calorimeters are foreseen for the instrumentation of the very forward region of the ILC detector, a luminometer designed to measure the rate of low angle Bhabha scattering events with a precision better than 10-3 and a low polar…
We present a candidate sensor for future spectroscopic applications, such as a Stage-5 Spectroscopic Survey Experiment or the Habitable Worlds Observatory. This type of charge-coupled device (CCD) sensor features multiple in-line amplifiers…
A new cryogenic noise calibration source for radio astronomy receivers is presented. Dissipated power is only 4.2 mW, allowing it to be integrated with the cold part of the receiver. Measured long-term stability, sensitivity to bias…
We experimentally show that the Inelastic Cooper-Pair Tunneling Amplifier (ICTA), implementing a DC-powered parametric amplification scheme, can achieve gain and noise performance similar to that of Josephson parametric amplifiers. Using…
The demand from industry to produce accurate acceleration measurements down to ever lower frequencies and with ever lower noise is increasing. Different vibration transducers are used today for many different purposes within this area, like…
MALTA2 is a depleted monolithic active pixel sensor (DMAPS) designed for tracking at high rates and typically low detection threshold of $\sim150\,\mathrm{e^-}$. A precise knowledge of the threshold is crucial to understanding the charge…
We demonstrate a radio-frequency parametric amplifier that exploits the gate-tunable quantum capacitance of an ultra high mobility two dimensional electron gas (2DEG) in a GaAs heterostructure at cryogenic temperatures. The prototype…
The calibration of sensors comprising inertial measurement units is crucial for reliable and accurate navigation. Such calibration is usually performed with specialized expensive rotary tables or requires sophisticated signal processing…