Related papers: Selective etching of PDMS: etching as positive res…
Stoichiometric silicon nitride has emerged as a widely used integrated photonic material owing to its high index of refraction, nonlinear optical properties, and broad transparency window spanning visible to mid-IR frequencies. However,…
We demonstrate a novel method for nanowire formation by natural selection during wet chemical etching in boiling Phosphoric acid. It is observed that wire lateral dimensions of sub-10 nm and lengths of 700 nm or more have been naturally…
We present results of a fabrication-process development for the lithographic pattern transfer into the sub-100nm range by combining electron-beam lithography and reactive dry etching to obtain high quality niobium-based light-sensitive…
Many promising applications of single crystal diamond and its color centers as sensor platform and in photonics require free-standing membranes with a thickness ranging from several micrometers to the few 100 nm range. In this work, we…
Gallium-based liquid metals have recently been found important in a variety of newly emerging applications such as room temperature metal 3D printing, direct writing of electronics and biomedicine etc. In all these practices, one frequently…
Using electrochemical impedance spectroscopy, we have devised a method of sensing the microscopic surface conditions on the surface of niobium as it is undergoing an electrochemical polishing (EP) treatment. The method uses electrochemical…
The article addresses the thermophysical properties of porous silicon (PS) samples produced through electrochemical (EC), metal-assisted chemical (MACE), and combined (MACE + EC) etching methods. The PS/MACE+EC sample's thermophysical…
Fabrication of complex molecular films of organic materials is one of the most important issues in modern nanoscience and nanotechnology. Soft materials with flexible properties have been given much attention and can be obtained through…
We have developed a poly(dimethylsiloxane) (PDMS) microfluidic chip to study the directional drying of a colloidal dispersion confined in a channel. Our measurements on a dispersion of silica nanoparticles once again revealed the…
Optical metasurfaces supporting resonances with high quality factors offer an outstanding platform for applications such as non-linear optics, light guiding, lasing, sensing, light-matter coupling, and quantum optics. However, their…
We study field effect transistor characteristics in etched single layer MoS2 nanoribbon devices of width 50nm with ohmic contacts. We employ a SF6 dry plasma process to etch MoS2 nanoribbons using low etching (RF) power allowing very good…
Powder of magnesium diboride was hot isostatically pressed using three qualitatively different cycles: cooling under pressure (DMCUP), "standard" cycle with pressure and temperature reduced simultaneously and isothermal presure release.…
We focused on polydimethylsiloxane (PDMS) as a substrate for replication, micropatterning, and construction of biologically active surfaces. The novelty of this study is based on the combina-tion of argon plasma exposure of micropatterned…
Fabrication techniques such as laser patterning offer excellent potential for low cost and large area device fabrication. Conductive polymers can be used to replace expensive metallic inks such as silver and gold nanoparticles for printing…
Radiative cooling is a passive cooling strategy with zero consumption of electricity. Although this technology can work well during optimal atmospheric conditions at nighttime, it is essential to achieve efficient radiative cooling during…
A cost effectively method to fabricate nanopores in silicon by only using the conventional wet-etching technique is developed in this research. The main concept of the proposed method is a two-step etching process, including a premier…
We report on mask-less, high resolution etching of diamond surfaces, featuring sizes down to 10 nm. We use a scanning electron microscope (SEM) together with water vapor, which was injected by a needle directly onto the sample surface.…
Granular nanostructure of electron beam resist had limited the ultimate resolution of electron beam lithography. We report a thermal process to achieve a uniform and homogeneous amorphous thin film of poly methyl methacrylate electron…
Doping of Si using the scanning probe hydrogen depassivation lithography technique has been shown to enable placing and positioning small numbers of P atoms with nanometer accuracy. Several groups have now used this capability to build…
We have produced thick-foil and fine-pitch gas electron multipliers (GEMs) using a laser etching technique. To improve production yield we have employed a new material, Liquid Crystal Polymer, instead of polyimide as an insulator layer. The…