Related papers: In-depth analysis of CIGS film for solar cells, st…
We present direct measurements of depth-resolved band gap variations of CuIn(1-x)Ga(x)Se2 thin-film solar cell absorbers. A new measurement technique combining parallel measurements of local thin-film interference and spectral…
The power conversion efficiency of an ultrathin CIGS solar cell was maximized using a coupled optoelectronic model to determine the optimal bandgap grading of the nonhomogeneous CIGS layer in the thickness direction. The bandgap of the CIGS…
We demonstrate a non-destructive approach to provide structural properties on the grain level for the absorber layer of kesterite solar cells. Kesterite solar cells are notoriously difficult to characterize structurally due to the…
A coupled optoelectronic model was implemented along with the differential evolution algorithm to assess the efficacy of grading the bandgap of the CZTSSe layer for enhancing the power conversion efficiency of thin-film CZTSSe solar cells.…
Power-conversion efficiency is a critical factor for the wider adoption of solar-cell modules. Thin-film solar cells are cheap and easy to manufacture, but their efficiencies are low compared to crystalline-silicon solar cells and need to…
Thin-film solar cells with CuIn$_x$Ga$_{1-x}$Se$_2$ (CIGS) absorber are still far below their efficiency limit, although lab cells reach already 19.9%. One important aspect is the homogeneity of the alloy. Large-scale simulations combining…
Cu(In,Ga)Se2 (CIGSe)-based solar cells are promising candidates for efficient sunlight harvesting. However, their complex composition and microstructure can change under operation conditions, for instance heating from sun light illumination…
In this paper, we present a physics-based analytical model for CIGS solar cells that describes the illumination- and temperature-dependent current-voltage (I-V) characteristics and accounts for the statistical shunt variation of each cell.…
A spatially resolved electroluminescence (EL) imaging experiment is developed to measure the local sheet resistance of the window layer, directly on the completed CIGS cell. Our method can be applied to the EL imaging studies that are made…
Record efficiency in chalcopyrite-based solar cells Cu(In,Ga)(S,Se)2 is achieved using a gallium gradient to increase the band gap of the absorber towards the back side. Although this structure has successfully reduced recombination at the…
The electronic and optical properties of CdGa2Te4 and ZnGa2Te4 were studied using first-principles DFT calculations. Band gaps were calculated using the GGA-PBESol functional. Both materials show promise for photovoltaic applications…
Sulfide chalcopyrite Cu(In,Ga)S2 (CIGS) is a wide bandgap semiconductor suitable for the top cell of a tandem solar device. Here we demonstrate significant improvements in absorber quality by alloying with Ag to form (Ag,Cu)(In,Ga)S2…
The thickness dependences of the photocurrent quantum yield and photoenergy parameters of silicon backside contact solar cells (BC SC) are investigated theoretically and experimentally. The surface recombination rate on the irradiated…
This study underscores the pivotal role of sodium (Na) supply in optimizing the optoelectronic properties of wide bandgap (~1.6 eV) Cu(In,Ga)S2 (CIGS) thin film absorbers for high efficiency solar cells. Our findings demonstrate that the…
Coating and reflecting thin films for energy harvesting purposes are interesting topics in both theoretical and experimental research. The thin film could help to enhance the absorption of the system via its specific optical properties…
Cu-based chalcogenides are promising materials for thin-film solar cells with more than 20% measured cell efficiency. Using first-principles calculations based on density functional theory, the optoelectronic properties of a group of…
We report a novel graded refractive index antireflection coating for III/V quadruple solar cells based on bottom-up grown tapered GaP nanowires. We have calculated the photocurrent density of an InGaP-GaAs-InGaAsP-InGaAs solar cell with a…
Sulfide Kesterite Cu2ZnSnS4 (CZTS), a nontoxic and low-cost photovoltaic material, has always being facing severe charge recombination and poor carrier transport, resulting in the cell efficiency record stagnating around 11% for years.…
A systematic survey and subsequent research have been made on MoTe2-based n-CdS/p-MoTe2/p+-CGS device in solar cell and photodetector field. The optimization has been established by altering the various properties of each constituent layer…
An optoelectronic optimization was carried out for an AlGaAs solar cell containing (i) an n-AlGaAs absorber layer with a graded bandgap and (ii) a periodically corrugated Ag backreflector combined with localized ohmic Pd-Ge-Au backcontacts.…