Related papers: Implementation of the Epics Device Support for Net…
The current status of the control system for a new high intensity proton accelerator, the JAERI-KEK Joint Project, is presented. The Phase 1 of the Joint-Project has been approved and recently started its construction at JAERI site at…
The large scientific projects present new technological challenges, such as the distributed control over a communication network. In particular, the middleware EPICS is the most extended communication standard in particle accelerators. The…
The SNS Project intends to integrate Conventional Facility Controls with its EPICS-based Accelerator and Target Control Systems. EPICS will therefore be used to provide distributed high-level access to all subsystems of the SNS conventional…
CEA Irfu Saclay is involved as partner in the ESS accelerator construction through different work-packages: controls for several RF test stands, for cryomodule demonstrators, for the RFQ coupler test and for the conditioning around 120…
We will use EPICS toolkit [1] to build a prototype for upgrading BEPC control system. The purposes are for the following three aspects: (1) Setup a network based distributed control system with EPICS. (2) Study some front-end control…
KEKB completed all of the technical milestones, and had offered important insights into the flavor structure of elementary particles, especially the CP violation. The accelerator control system at KEKB and injector linac was initiated by a…
Experimental Physics and Industrial Control System (EPICS) is a software tool that during last years has become relevant as a main framework to deploy distributed control systems in large scientific environments. At the moment, ESS Bilbao…
Many large accelerator facilities have adopted the open-source EPICS software as the quasi-industry standard for control systems. They typically have access to their own electronics laboratory and dedicated personnel for control system…
Each accelerator control system has a variety of measurement devices. One of the most common types of instrument interfaces used for their control is a serial (RS-232) bus. It is inexpensive and adequate for relatively simple measurement…
This article describes concepts and mechanisms used in porting of EPICS (Experimental Physical and Industrial Control System) codes to platform of operating system UNIX. Without destruction of EPICS architecture, new features of EPICS…
Implementation and commissioning of the EPICS based control system for the ISAC radioactive beam facility was completed. The target ion source, mass separator, and low-energy beam-lines started beam production for experiments. In parallel,…
The Framework is one of the subprojects of the Joint COntrols Project (JCOP), which is collaboration between the four LHC experiments and CERN. By sharing development, this will reduce the overall effort required to build and maintain the…
At least 25 kinds of detector-like devices need to be integrated in Phase I of the High Energy Photon Source (HEPS), and the work needs to be carefully planned to maximise productivity with highly limited human resources. After a systematic…
An important component of EPICS (Experimental Physics and Industrial Control System) is iocCore, which is the core software in the IOC (input/output controller) front-end processors. At ICALEPCS 1999 a paper was presented describing plans…
Measurement of high-power proton beam-halo formation is the ongoing scientific experiment for the Low Energy Demonstration Accelerator (LEDA) facility. To attain this measurement goal, a 52-magnet beam line containing several types of beam…
The EPICS based control system of the ISAC radioactive beam facility supervises several sub-systems, which are controlled by PLCs. Most of the devices are protected by non-trivial interlocks, which are implemented with ladder-logic…
As an accelerator control system survives over several years, it is often the case that new subsystems are introduced into the original control system. The control system for the KEK electron/positron injector-linac has been using Unix…
The Advanced Photon Source is now in its fifth year of routine beam production. The EPICS-based [1] control system has entered the phase in its life cycle where new control algorithms must be implemented under increasingly stringent…
The Allen-Bradley ControlLogix line of pro-grammable logic controllers (PLCs) offers several in-terfaces: Ethernet, ControlNet, DeviceNet, RS-232 and others. The ControlLogix Ethernet interface module 1756-ENET uses EtherNet/IP, the…
The Global Accelerator Network is a proposed model for remote operation of a future large accelerator by the partners of an international collaboration. The remote functionality would include not only routine operation and machine studies,…