Related papers: Technology Update of a Control System Trough Corba…
Louisiana State University Center for Advanced Microstructures and Devices (CAMD) began a control system upgrade project in early 1997. At the time, the storage ring was controlled by a VAX/VMS system, primarily using CAMAC for I/O. The…
The share of the top 500 supercomputers with NVIDIA GPUs is now over 25% and continues to grow. While fault tolerance is a critical issue for supercomputing, there does not currently exist an efficient, scalable solution for CUDA…
With the development of intelligent connected vehicle technology, human-machine shared control has gained popularity in vehicle following due to its effectiveness in driver assistance. However, traditional vehicle following systems struggle…
Different hardware platforms and their associated real time operating systems that can be used in an educational laboratory for illustrating engine electronic control unit hardware in the loop testing are presented and compared in this…
Run Time Assurance (RTA) Systems are online verification mechanisms that filter an unverified primary controller output to ensure system safety. The primary control may come from a human operator, an advanced control approach, or an…
The implementation of uplink HARQ in a Cloud- Radio Access Network RAN (C-RAN) architecture is constrained by the two-way latency on the fronthaul links connecting the Remote Radio Heads (RRHs) with the Baseband Units (BBUs) that perform…
The BaBar online data acquisition (DAQ) system includes approximately fifty Unix systems that collectively implement the level-three trigger. These systems all run the same code. Each of these systems has its own state, and this state is…
Point cloud processing is a computational bottleneck in autonomous driving systems, especially for real-time applications, while energy efficiency remains a critical system constraint. This work presents FPPS, an FPGA-accelerated point…
The stochastic nature of public transport systems leads to headway variability and bus bunching, causing both operator and passenger cost to increase significantly. Traditional strategies to counter bus bunching, including bus-holding,…
This paper presents a novel mechatronic setup intended for providing respiratory support to patients suffering from pulmonary failure. The setup relies upon the circulation of an oxygenated perfluorocarbon (PFC) through the abdominal…
The coupling disturbance between the manipulator and the unmanned aerial vehicle (UAV) deteriorates the control performance of system. To get high performance of the aerial manipulator, a robust fractional order fast terminal sliding mode…
NAND flash-based Solid State Drives (SSDs), which are widely used from embedded systems to enterprise servers, are enhancing performance by exploiting the parallelism of NAND flash memories. To cope with the performance improvement of SSDs,…
Fully understanding performance is a growing challenge when building next-generation cloud systems. Often these systems build on next-generation hardware, and evaluation in realistic physical testbeds is out of reach. Even when physical…
Each accelerator control system has a variety of measurement devices. One of the most common types of instrument interfaces used for their control is a serial (RS-232) bus. It is inexpensive and adequate for relatively simple measurement…
Fault tolerance is achieved through multiply redundant hardware systems in large civil aircraft. This means of achieving fault tolerance is infeasible for small compact unmanned aerial vehicles. In this paper we apply a fault tolerant…
Real-time embedded platforms with resource constraints can take the benefits of mixed-criticality system where applications with different criticality-level share computational resources, with isolation in the temporal and spatial domain. A…
In this paper, the control problem for underactuated systems in the presence of external disturbances and model uncertainties is considered. An adaptive fuzzy sliding mode controller (AFSMC) is proposed to solve the problem, satisfying the…
This comprehensive review article delves into the intricate realm of fault-tolerant control (FTC) schemes tailored for robotic manipulators. Our exploration spans the historical evolution of FTC, tracing its development over time, and…
Rising electricity demand and the growing integration of renewables are intensifying congestion in transmission grids. Grid topology optimization through busbar splitting (BuS) and optimal transmission switching can alleviate grid…
We introduce OpenCAMS (Open-Source Connected and Automated Mobility Co-Simulation Platform), an open-source, synchronized, and extensible co-simulation framework that tightly couples three best-in-class simulation tools: (i) SUMO, (ii)…