Related papers: Steady-State Creep Analysis of Pressurized Pipe We…
We numerically investigate the athermal creep deformation of amorphous materials having a wide range of stability. The imposed shear stress serves as the control parameter, allowing us to examine the time-dependent transient response…
The aim of the paper is to derive the exact analytical expressions for torsion and bending creep of rods with the Norton-Bailey, Garofalo and Naumenko-Altenbach-Gorash constitutive models. These simple constitutive models, for example, the…
Yield stress fluids display complex dynamics, in particular when driven into the transient regime between the solid and the flowing state. Inspired by creep experiments on dense amorphous materials, we implement mesocale elasto-plastic…
Thermal fluctuations, geometric exclusion, and external driving all govern the mechanical response of dense particulate suspensions. Here, we measure the stress-strain response of quasi-two-dimensional flow-stabilized microsphere heaps in a…
We study the creep behavior of a disordered brittle material (concrete) under successive loading steps, using acoustic emission and ultrasonic sensing to track internal damage. The primary creep rate is observed to follow a (Omori-type)…
Yield stress materials fail when the imposed stress crosses a critical threshold. A well-known dynamical response to the applied stress is the phenomenon of creep where the cumulative deformation grows sublinearly with time, prior to…
A microfluidic approach to probing the first normal stress difference from single-point pressure measurements in transient shear flows is presented. Using an original experimental design, we examine the near-zero-mean pulsatile flow of…
Pressure-relief valves, often the critical last line of defence in process engineering, are known to be susceptible to valve chatter. Such behaviour has been shown to arise from a flutter instability, or Hopf bifurcation, associated with…
Dense suspensions of hard particles in a Newtonian liquid can be jammed by shear when the applied stress exceeds a certain threshold. However, this jamming transition from a fluid into a solidified state cannot be probed with conventional…
A numerical bifurcation analysis of the electrically driven plane sheet pinch is presented. The electrical conductivity varies across the sheet such as to allow instability of the quiescent basic state at some critical Hartmann number. The…
A method is presented for the evaluation of the permeability-porosity relationship in a low-permeability porous material using the results of a single transient test. This method accounts for both elastic and non-elastic deformations of the…
Creep is defined as time-dependent deformation and rupture processes taking place within a material subjected to a constant applied stress smaller than its athermal, time-independent strength. This time-dependence is classically attributed…
A novel perturbation method for the stabilization of unstable intermediate states of hysteresis loop (i.e. S-shaped curve) is proposed. This method only needs output signals of the system to construct the perturbation form without…
We formulate two estimation problems for pipeline systems in which measurements of compressible gas flow through a network of pipes is affected by time-varying injections, withdrawals, and compression. We consider a state estimation problem…
When submitted to a constant mechanical load, many amorphous solids display power law creep followed by fluidization. A fundamental understanding of these processes is still far from being achieved. Here, we characterize creep and…
Flow in soft materials encompasses a wide range of viscous, plastic and elastic phenomena which provide challenges to modelling at the microscopic level. To create a controlled flow, we perform falling ball viscometry tests on packings of…
The nonequilibrium dynamics of diffusion-mediated plasticity and creep in materials subjected to constant load at high homologous temperatures is studied atomistically using Phase Field Crystal (PFC) methods. Creep stress and grain size…
Creep tests on heterogeneous materials under subcritical loading typically show a power-law decaying strain rate before failure, with the exponent often considered material-dependent but independent of applied stress. By imposing successive…
We numerically and analytically analyze the startup continuous shear rheology of heavily entangled rigid rod polymer fluids based on our self-consistent, force-level theory of anharmonic tube confinement. The approach is simplified by…
Creep is a time-dependent deformation of solids at relatively low stresses, leading to the breakdown with time. Here we propose a simple model for creep failure of disordered solids, in which temperature and stress are controllable. Despite…