Related papers: Fiber R and D for the CMS HCAL

A novel 3-D calorimeter, composed of about 7500 LYSO cubes, is the key and crucial detector of the High Energy cosmic-Radiation Detection (HERD) facility to be installed onboard the China Space Station. Energy deposition from cosmic ray in…

Hadronic Forward(HF) detector is one of the sub-detectors of the CMS. It plays an important role in the measurement of forward jets and missing energy. HF is situated on both sides of the CMS interaction point, at about $\pm$11 m, covers…

Pd/Y multilayers are high reflectance mirrors designed to work in the 7.5-11 nm wavelength range. Samples, prepared by magnetron sputtering, are deposited with or without B4C barrier layers located at the interfaces of Pd and Y layers to…

Optical spectroscopy techniques such as differential reflectance and transmittance have proven to be very powerful techniques to study 2D materials. However, a thorough description of the experimental setups needed to carry out these…

To face the higher levels of radiation due to the 10-fold increase in integrated luminosity during the High-Luminosity LHC, the CMS detector will replace the current Calorimeter Endcap (CE) using the High-Granularity Calorimeter (HGCAL)…

The performance of the CMS electromagnetic calorimeter upgraded readout electronics, developed for the High-Luminosity phase of the LHC, is discussed. Data collected in two beam test campaigns conducted in 2018 and 2021 at the H4 and H2…

The activities towards the fabrication and test of a 1 m3 semi-digital hadronic calorime- ter are reviewed. The prototype sampling planes would consist of 1 m2 Micromegas chambers with 1 cm2 granularity and embedded 2 bits readout suitable…

The CALICE collaboration is currently developing engineering prototypes of electromagnetic and hadronic calorimeters for a future linear collider detector. This detector is designed to be used in particle-flow based event reconstruction. In…

We have exposed seven full length production quality crystals of the electromagnetic calorimeter (ECAL) of the CMS detector to a 20 GeV/c proton beam at the CERN PS accelerator. The exposure was done at fluxes of 10**12 p/cm**2/h and 10**13…

We introduce an all-glass, vacuum tight, fiber-integrated and alkali compatible spectroscopy device consisting of two conventional optical fibers spliced to each end of a capillary. This is mainly realized through a decentered splicing…

The electronic system developed for the SpaCal lead/scintillating-fibre calorimeters of the H1 detector in operation at the HERA ep collider is described in detail and the performance achieved during H1 data-taking is presented. The 10 MHz…

We study the light output, light collection efficiency and signal timing of a variety of organic scintillators that are being considered for the upgrade of the hadronic calorimeter of the CMS detector. The experimental data are collected at…

The design of the ILD AHCAL is optimized to make the best use of the PFA and its active layers are composed of about eight million scintillator tiles readout by SiPMs. If there is optical crosstalk between the tiles, the calorimeter…

Calorimetry at future linear colliders could be based on a particle flow approach where granularity is the key to high jet energy resolution. Among different technologies, Micromegas chambers with 1 cm2 pad segmentation are studied for the…

This article describes the design, construction and use of a calibration and monitoring system, based on movable 137Cs gamma-ray sources, for the ATLAS Tile Calorimeter (TileCal). The sources, propelled by a water-based liquid through tubes…

Precision calorimetry using highly granular sampling calorimeters is being developed based on the particle flow concept within the CALICE collaboration. One design option of a hadron calorimeter is based on silicon photomultipliers (SiPMs)…

In order to enable high quality lens designs using calcium fluoride (CaF2) and Heraeus Infrasil 301 (Infrasil) for cryogenic operating temperatures, we have measured the absolute refractive index of these two materials as a function of both…

The Semi-Digital Hadronic Calorimeter (SDHCAL) is proposed to equip the future ILC detector. A technological prototype of the SDHCAL developed within the CALICE collaboration has been extensively tested in test beams. We review here the…

The performance of scintillator counters with embedded wavelength-shifting fibers has been measured in the Fermilab Meson Test Beam Facility using 120 GeV protons. The counters were extruded with a titanium dioxide surface coating and two…

The pixel detector is the innermost tracking device of the CMS experiment at the LHC. It is built from two independent sub devices, the pixel barrel and the end disks. The barrel consists of three concentric layers around the beam pipe with…