Related papers: Simulating a dual-recycled gravitational wave inte…
The double wall-ring (DWR) rotational configuration is nowadays the instrument of choice regarding interfacial shear rheometers (ISR) in rotational configurations. Complex numerical schemes must be used in the analysis of the output data in…
The design of new low-mechanical-loss, high reflectivity mirrors is crucial in the development of the next generation of gravitational-wave observatories. Currently, the state-of-the-art amorphous multilayer reflective coatings which are…
Hardware injections are simulated gravitational-wave signals added to the Laser Interferometer Gravitational-wave Observatory (LIGO). The detectors' test masses are physically displaced by an actuator in order to simulate the effects of a…
We carried out a computer simulation of a large gravitational wave (GW) interferometer using the specifications of the LIGO instruments. We find that if in addition to the carrier, a single sideband offset from the carrier by the fsr…
We calculate the response of an ideal Michelson interferometer incorporating both dual recycling and squeezed light to gravitational waves. The photon counting noise has contributions from the light which is sent in through the input ports…
Using the force-susceptibility formalism of linear quantum measurements, we study the dynamics of signal recycled interferometers, such as LIGO-II. We show that, although the antisymmetric mode of motion of the four arm-cavity mirrors is…
The sensitivity of ground-based gravitational wave (GW) detectors will be improved in the future via the injection of frequency-dependent squeezed vacuum. The achievable improvement is ultimately limited by losses of the interferometer…
All first-generation large-scale gravitational wave detectors are operated at the dark fringe and use a heterodyne readout employing radio frequency (RF) modulation-demodulation techniques. However, the experience in the currently running…
We study frequency dependent (FD) input-output schemes for signal-recycling interferometers, the baseline design of Advanced LIGO and the current configuration of GEO 600. Complementary to a recent proposal by Harms et al. to use FD input…
Gravitational wave detectors such as KAGRA, a 3-km long underground laser interferometer in Japan, require elaborate passive and active seismic isolation of their mirrors. With the aim of detecting passing gravitational waves that create a…
Suspended optics in gravitational wave (GW) observatories are susceptible to alignment perturbations, particularly slow drifts over time, due to variations in temperature and seismic levels. Such misalignments affect the coupling of the…
Intelligent reflecting surface (IRS) is envisioned as a revolutionary technology for future wireless communication systems since it can intelligently change radio environment and integrate it into wireless communication optimization.…
In order to achieve full detection sensitivity at low frequencies, the mirrors of interferometric gravitational wave detectors must be isolated from seismic noise. The VIRGO vibration isolator, called 'superattenuator', is fully effective…
Intelligent reflecting surface (IRS) are able to amend radio propagation condition tasks on account of its functional properties in phase shift optimizing. In fact, there exists geometry manifold in the base-station (BS) beamforming matrix…
Fundamental sensitivity of an optical interferometric gravitational wave detector increases with increase of the optical power which, in turn, limited because of the opto-mechanical parametric instabilities of the interferometer. We propose…
The ``optical springs'' regime of the signal-recycled configuration of laser interferometric gravitational-wave detectors is analyzed taking in account optical losses in the interferometer arm cavities. This regime allows to obtain…
There exists the standard quantum limit (SQL), derived from Heisenberg's uncertainty relation, in the sensitivity of laser interferometer gravitational-wave detectors. However, in the context of a full quantum-mechanical approach, SQL can…
We propose a novel approach to detect gravitational waves based on a semi-rigid detector. The approach relies upon the time delay that the light takes to travel from a fixed mirror at the end of a rigid bar to a nearby free mirror. We show…
We present a time-frequency method to detect gravitational wave signals in interferometric data. This robust method can detect signals from poorly modeled and unmodeled sources. We evaluate the method on simulated data containing noise and…
Thermal lensing in resonant optical interferometers such as those used for gravitational wave detection is a concern due to the negative impact on control signals and instrument sensitivity. In this paper we describe a method for monitoring…