Related papers: A new emitter for electrospray and electrohydrodyn…
Despite a rigorous analysis of nonlinear electrohydrodynamics of a liquid droplet deformation in air, its influence on the surrounding gas phase has received less attention. We observed, air circulations created due to large deformation…
Microemulsion droplets (oil in water stabilized by a surfactant film) are progressively decorated with increasing amounts of poly ethylene- oxide (PEO) chains anchored in the film by the short aliphatic chain grafted at one end of the PEO…
Pulsating jet is one of the common working modes in electrohydrodynamic printing (EHDP) that process is highly affected by operating parameters and material properties. In this paper, the processes of pulsating jet for liquids with…
Astrophysical jets are often observed as bent or curved structures. We also know that the different jet sources may be binary in nature, which may lead to a regular, periodic motion of the jet nozzle, an orbital motion or precession. Here,…
Dielectrophoresis is an electric field-based technique for moving neutral particles through a fluid. When used for particle separation, dielectrophoresis has many advantages compared to other methods, providing label-free operation with…
Direct numerical simulations of electrospinning and electrospraying are computationally demanding due to large-scale separation between the needle and the tip-to-collector distance. The cone-jet mode that occurs in the vicinity of the…
Complex structures on a material surface can significantly reduce total secondary electron emission from that surface. A velvet is a surface that consists of an array of vertically standing whiskers. The reduction occurs due to the capture…
Nanopores (NPs) grown by anodizing can be partially hidden beneath a relatively compact surface oxide layer, which limits the volumetric surface area of these nanostructures. In this work, nitinol (NiTi) alloy was anodized in an electrolyte…
Fused Filament Fabrication is an additive manufacturing technique in which molten thermoplastic polymers are extruded through a nozzle. Therefore, the interplay between the viscoelastic nature of the polymer melt, temperature, printing…
A delayed detached eddy simulation of a sub-scale cold-gas dual-bell nozzle flow at high Reynolds number and in sea-level mode is carried out at nozzle pressure ratio NPR=45.7. In this regime the over-expanded flow exhibits a symmetric and…
Electrospray thrusters promise compact, high specific impulse propulsion for small spacecraft, yet ground characterization remains confounded by secondary species emission and incomplete diagnostics of neutral products. To address these…
We study experimentally and numerically the onset of tip streaming in an electrified droplet. The experiments show that, for a sufficiently small dimensionless conductivity, the droplet apex oscillates before ejecting a liquid jet. This…
Spray atomization process involves complex multi-phase phenomena. Abundant literature and validation of spray modelling for industrial applications like fuel injection in internal combustion and turbine jet engines are available. However,…
We investigate the linear stability of a hydrodynamic relativistic flow of magnetized plasma in the force--free approximation. We considered the case of light cylindrical jet in cold and dense environment, so the jet boundary remains at…
The liquid cone-jet mode can be produced upon stimulation by a co-flowing gas sheath. Most applications deal with the jet breakup, leading to either of two droplet generation regimes: jetting and dripping. The cone-jet flow pattern is…
Attempts to use Electrohydrodynamic (EHD) flow for propulsion have been made since the last century [1]. Limited success has been registered particularly due to the inhomogeneous generation of the thrust, and also the very light weight and…
Conductive elastomers present desirable qualities for sensing pressure in-vivo, such as high piezoresistance in tiny volumes, conformability and, biocompatibility. Many PDMS-based electrically conductive nanocomposites however, are…
Electrolytically generated gas bubbles can significantly hamper the overall electrolysis efficiency. Therefore it is crucial to understand their dynamics in order to optimise water electrolyzer systems. Here we demonstrate a distinct…
Electrowetting is a commonly used tool to manipulate sessile drops on hydrophobic surfaces. By applying an external voltage over a liquid and a dielectric-coated surface, one achieves a reduction of the macroscopic contact angles for…
Elliptic nozzle geometry is attractive for mixing enhancement of supersonic jets. However, jet dynamics, such as flapping, gives rise to high-intensity tonal sound. We experimentally manipulate the supersonic elliptic jet morphology by…