Related papers: Calibration of Scanning Thermal Microscope using O…
Colloidal probes are often used in force microscopy when the geometry of the tip-sample interaction should be well controlled. Their calibration requires the understanding of their mechanical response, which is very sensitive to the details…
Fourier ptychographic microscopy (FPM) is a recently proposed quantitative phase imaging technique with high resolution and wide field-of-view (FOV). In current FPM imaging platforms, systematic error sources come from the aberrations, LED…
Nanoscale thermal properties are becoming of extreme importance for modern electronic circuits that dissipate increasing power on the length scale of few tens of nanometers, and for chemical and physical properties sensors and biosensors…
We have studied the thermal conductivity of confined superfluids on a bar-like geometry. We use the planar magnet lattice model on a lattice $H\times H\times L$ with $L \gg H$. We have applied open boundary conditions on the bar sides (the…
This study is concerned with the design of a Mueller imaging polarimeter for the visualization of spatially-varying Mueller matrix fields. A simplified calibration procedure is advocated, where all the optical elements are calibrated…
We propose a straightforward sample-based technique to calibrate the axial detection in 3D single molecule localization microscopy (SMLM). Using microspheres coated with fluorescent molecules, the calibration curves of PSF-shaping- or…
We present a method for calibrating the response of a phase-only spatial light modulator in nonlinear microscopy. Our method uses the microscope image itself as calibration measurement and requires no additional hardware components. Our…
Primary power standards in the microwave domain are realized using a calorimetric technique, usually identified with the used measurement system, i.e., the microcalorimeter. It is adjusted for measurement of power ratios with a relative…
We present an advanced scanning probe microscopy system enhanced with artificial intelligence (AI-SPM) designed for self-driving atomic-scale measurements. This system expertly identifies and manipulates atomic positions with high…
The usual method for determining the sensitivity curve of a TXRF spectrometer relies on calibration using a set of vendor-certified concentration values of reference calibration standards. These samples, which are certified by the provider,…
The estimation of wall thermal properties by \emph{in situ} measurement enables to increase the reliability of the model predictions for building energy efficiency. Nevertheless, retrieving the unknown parameters has an important…
We present a simple method for fast and cheap thermal analysis on supercooled glass-forming liquids. This "Thermalization Calorimetry" technique is based on monitoring the temperature and its rate of change during heating or cooling of a…
We propose a novel experimental probe for cold atomic gases analogous to the scanning tunnelling microscope (STM) in condensed matter. This probe uses the coherent coupling of a single particle to the system. Depending on the measurement…
A silicon-based fine granularity calorimeter is a potential technology for the future International Linear Collider ILC, the future circular collider CEPC, and is also the chosen technology for the upgraded CMS experiment of the Large…
Material thermal properties characterization at nanoscales remains a challenge even if progresses were done in developing specific characterization techniques like the Scanning Thermal Microscopy (SThM). In the present work, we propose a…
Since the internal temperature is less accessible than surface temperature, there is an urgent need to develop accurate and real-time estimation algorithms for better thermal management and safety. This work presents a novel framework for…
The energy calibration of calorimeters at collider experiments, such as the ones at the CERN Large Hadron Collider, is crucial for achieving the experiments physics objectives. Standard calibration approaches have limitations that become…
In this paper new characterization equipment for thermal interface materials is presented. Thermal management of electronic products relies on the effec-tive dissipation of heat. This can be achieved by the optimization of the system design…
In this paper we describe a spatial decomposition of the thermal conductivity, what we name "site-projected thermal conductivity", a gauge of the thermal conduction activity at each site. The method is based on the Green-Kubo formula and…
Calibration is one area in measurement where our country is still in the process of improvement. The absence of confirmed approaches and actions for identifying the features of calibration baths by numerous laboratories disallowed them to…