Related papers: Performance Analyses of the Newly Developed Operat…
The task of this work was to design and later produce a low-power (single supply 5 - 30 V, dual supply +-2.5 V and +-15 V) rail-to-rail operational amplifier aRD820 with low voltage noise (<4 uV, p-p. 0.1 to 10 Hz), ultralow input bias…
In this paper, a two-stage ultra-low-power operational amplifier is designed, and a comparative analysis of the proposed subthreshold complementary amplifier is presented between 180nm, 90nm, and 45nm CMOS technology. The proposed…
A four-stage operational transconductance amplifier (OTA) for ultra-low-power applications is introduced in this paper. The proposed circuit inclusive of frequency compensation requires minimal transistor count and passives, overcoming the…
For the first time the cumulative distribution function of the crossover frequency of a contemporary operational amplifier ADA4898-2 is experimentally studied. Using a USB Lock-In amplifier, which allows automatic frequency sweep of the…
We report on the design and characterization of a high-power amplifier with an output power of 36.5 dBm for a frequency range of 50 MHz to 1000 MHz with a total gain of 40 dB. The amplifier is optimized for driving acousto-optic and…
Operational Amplifiers (Op-Amps) play a crucial role in the field of biomedical engineering, as they enable signal amplification and processing in various medical devices. With the increasing demand for portable and low-power biomedical…
A near threshold all-optical backaction amplifier is realized. Operating near threshold in an integrated micronscale architecture allows a nearly three orders of magnitude improvement in both gain and optical power requirements over the…
Analog-to-digtial (A/D) conversion plays a crucial role when it comes to the design of energy-efficient and fast signal processing systems. As its complexity grows exponentially with the number of output bits, significant savings are…
In the past few years, advancements in the field of nano circuit design has become tougher than the demand. Low power devices have emerged tremendously.Both voltage mode aswell as current mode devices have proven alternative to each other…
An observer based adaptive detection methodology (ADM) is proposed for estimating frequency and its rate of change (RoCoF) of the voltage and/or current measurements acquired from an instrument transformer. With guaranteed convergence and…
In this paper a CMOS operational amplifier is presented which operates at 2V power supply and 1microA input bias current at 0.8 micron technology using non conventional mode of operation of MOS transistors and whose input is depended on…
This paper describes a pipelined analog-to-digital converter (ADC) employing a power and area efficient architecture. The adjacent stages of a pipeline share operational amplifiers. In order to keep accuracy of the amplifiers in the first…
This paper presents analysis results of the operational transconductance amplifiers (OTAs) that combine feedforward paths and multistage amplifiers to achieve high-gain wideband operation as well as frequency compensation. To analyze…
A transimpedance amplifier has been designed for scanning tunneling microscopy (STM). The amplifier features low noise (limited by the Johnson noise of the 1 G{\Omega} feedback resistor at low input current and low frequencies), sufficient…
Typical bio-signal processing front-ends are designed to maximize the quality of the recorded data, to allow faithful reproduction of the signal for monitoring and off-line processing. This leads to designs that have relatively large area…
In this paper a CMOS two stage operational amplifier has been presented which operates at 1.8 V power supply at 0.18 micron (i.e., 180 nm) technology and whose input is depended on Bias Current. The op-amp provides a gain of 63dB and a…
A low-noise amplifier (LNA) amplifies a very low-power signal without significantly degrading its signal-to-noise ratio. This paper provides the design of a linear low noise amplifier with the transistor BFP 640 using bilateral approach…
Analog to Digital Converters (ADCs) are a major contributor to the energy consumption on the receiver side of millimeter-wave multiple-input multiple-output (MIMO) systems with large antenna arrays. Consequently, there has been significant…
Recording reliably extracellular neural activities isan essential prerequisite for the development of bioelectronicsand neuroprosthetic applications. Recently, a fully differential,2-stage, integrating pre-amplifier was proposed for…
This paper presents a new auto zeroing technique that combines very high-speed operation, low power consumption, and low input switching interferences. This technique has been applied to the design of CMOS flash Analog-to-Digital converter…