Related papers: Technical challenges designing a prototype common …
The PCIe400 is a generic readout board designed for high-throughput data acquisition in future high-energy physics experiments. It interfaces up to 48 bidirectional links supporting custom protocols from 1 to 26 Gbps to modern back-end…
The upgraded LHCb detector, due to start datataking in 2022, will have to process an average data rate of 4~TB/s in real time. Because LHCb's physics objectives require that the full detector information for every LHC bunch crossing is read…
The LHCb experiment at CERN has undergone a comprehensive upgrade, including a complete re-design of the trigger system into a hybrid-architecture, software-only system that delivers ten times more interesting signals per unit time than its…
In 2019, the LHCb experiment at CERN will undergo a major upgrade where its detector electronics and the entire readout system will be replaced. The goal is to read-out all events at the full LHC frequency of 40 MHz, reaching a total data…
The LHCb experiment is designed to perform high-precision measurements of CP violation and search for New Physics using the enormous flux involving beauty and charm quarks produced at the LHC. The operation and the results obtained from the…
High Energy Physics (HEP) data acquisition systems are often built from high-end FPGAs. As such systems scale in the HL-LHC era, severe under-utilization of FPGA transceivers can occur because front-end links prioritize radiation hardness…
Starting in 2022, the upgraded LHCb detector will collect data with a pure software trigger. In its first stage, reducing the rate from 30MHz to about 1MHz, GPUs are used to reconstruct and trigger on B and D meson topologies and high-pT…
The LHCb upgrade represents a major change of the experiment. The detectors have been almost completely renewed to allow running at an instantaneous luminosity five times larger than that of the previous running periods. Readout of all…
The upgraded LHCb detector has started its Run 3 of data taking in 2022, with a completely overhauled DAQ system, reading out and processing the full detector data at every LHC bunch crossing (30 MHz average rate). At the same time, an…
COFFEE series is a HVCMOS pixel sensor using the advanced 55 nm process, currently being developed for the Upstream Pixel (UP) tracker of the LHCb Upgrade II. To ensure that COFFEE will be able to handle the particle hit rates at UP…
The CMS collaboration is building a new inner tracking pixel detector for the High-Luminosity LHC. Each pixel readout chip will be controlled with a single serial input stream at 160 Mbps and will send out data via four current mode logic…
This work gives an overview of the PCI-Express board $\pi$LUP, focusing on the motivation that led to its development, the technological choices adopted and its performance. The $\pi$LUP card was designed by INFN and University of Bologna…
The LHCb experiment at CERN is undergoing an upgrade in preparation for the Run 3 data taking period of the LHC. As part of this upgrade the trigger is moving to a fully software implementation operating at the LHC bunch crossing rate. We…
Belle II is a new-generation B-factory experiment, dedicated to exploring new physics beyond the standard model of elementary particles in the flavor sector. Belle~II started data-taking in April 2018, using a synchronous data acquisition…
A front-end readout electronics system has been developed for silicon strip detectors. The system uses an application specific integrated circuit (ASIC) ATHED to realize multi-channel E&T measurement. The slow control of ASIC chips is…
As from the run 3 of CERN LHC scheduled in 2022, the upgraded ALICE experiment will use a Common Readout Unit (CRU) at the heart of the data acquisition system. The CRU, based on the PCIe40 hardware designed for LHCb, is a common interface…
The increasing computing power and bandwidth of FPGAs opens new possibilities in the field of real-time processing of high-energy physics data. The LHCb experiment has implemented a cluster-finder FPGA architecture aimed at reconstructing…
The LHCb experiment will operate at a luminosity of $2\times10^{33}$ cm$^{-2}$s$^{-1}$ during LHC Run 3. At this rate the present readout and hardware Level-0 trigger become a limitation, especially for fully hadronic final states. In order…
The LHCb detector will be upgraded during the Long Shutdown 2 (LS2) of the LHC in order to cope with higher instantaneous luminosities and to read out the data at 40 MHz using a trigger-less readout system. The current LHCb main tracking…
The LHCb (Large Hadron Collider beauty) experiment is designed to study differences between particles and anti-particles as well as very rare decays in the charm and beauty sector at the LHC (Large Hadron Collider). The detector will be…