Related papers: Low Temperature Deposition of Functional Thin Film…
Combining topological insulators (TIs) and magnetic materials in heterostructures is crucial for advancing spin-based electronics. Magnetic insulators (MIs) can be deposited on TIs using the spin-spray process, which is a unique non-vacuum,…
We report the development of broadband solar absorber coatings based on titanium suboxide composite thin films on aluminium substrates. The films are fabricated via scalable DC magnetron sputtering using a Ti target, followed by…
In this work, the authors fabricated Cu2O porous nanostructured films (PNFs) on glass slide substrates by the newly developed positive bias deposition approach in a balanced magnetron sputtering (MS) system. It was found that the surface…
One of many challenges for niobium (Nb) based superconducting devices is the improvement over the surface morphology and superconducting properties as well as the reduction of defects. We employed a novel deposition technique, i.e. biased…
High-quality factor plasmonic devices are crucial components in the fields of nanophotonics, quantum computing and sensing. The majority of these devices are required to be fabricated on non-lattice matched or transparent amorphous…
This study aims towards a systematic reciprocity of the tunable synthesis parameters - partial pressure of N$_2$ gas, ion energy (\Ei) and Ti interface in TiN thin film samples deposited using ion beam sputtering at ambient temperature…
Antiferromagnets are promising materials for future opto-spintronic applications since they show spin dynamics in the THz range and no net magnetization. Recently, layered van der Waals (vdW) antiferromagnets have been reported, which…
Electronic devices are progressively fabricated on flexible substrates allowing new fields of applications. A maskless and very flexible structuring process is offered by ablation using ultra-short pulse laser irradiation. Usually, certain…
We developed functional surfaces of laser-microstructured silicon coated with blends of polystyrene (PS) and poly(N-isopropylacrylamide) (PNIPAM) and we study their switching wetting behavior between hydrophilicity and hydrophobicity. Large…
Three-dimensional (3D) topological insulators (TIs) are candidate materials for various electronic and spintronic devices due to their strong spin-orbit coupling and unique surface electronic structure. Rapid, low-cost preparation of…
The Bi1-xSbx was the first 3D topological insulator found in nature. It presents a complex electronic structure with topological to trivial transition and a semimetallic to semiconductor transition, both achieved by changing the x fraction…
SrTiO$_{3}$ is one of the most popular insulating single-crystal substrates for various complex-oxide thin film growths, because of its good lattice match with many complex oxide films. Here, we show that a common thin film processing…
We investigated the transport titanium ions produced in a reactive high-power impulse magnetron sputtering (HiPIMS) device used for TiN coating deposition. Time-resolved mass spectrometry measurements of ionized sputtered atoms correlated…
Superconducting resonators used in millimeter-submillimeter astronomy would greatly benefit from deposited dielectrics with a small dielectric loss. We deposited hydrogenated amorphous silicon films using plasma-enhanced chemical vapor…
To integrate plasmonic devices into industry, it is essential to develop scalable and CMOS compatible plasmonic materials. In this work, we report high plasmonic quality titanium nitride (TiN) on c-plane sapphire by plasma enhanced atomic…
Investigation of transport properties is fundamental for characterizing electronic properties and phase transitions. However, most of the transport measurements on conductive layers have been performed at macroscopic scales, and thus the…
Entropy stabilization has garnered significant attention as a new approach to designing novel materials. Much of the work in this area has focused on bulk ceramic processing, leaving entropy-stabilized thin films relatively underexplored.…
Thin films of TiN were sputter-deposited onto Si and sapphire wafers with and without SiN buffer layers. The films were fabricated into RF coplanar waveguide resonators, and internal quality factor measurements were taken at millikelvin…
Metal mixed polymers are a cheap and effective way to produce flexible metals and superconductors. As part of an on-going effort to learn how to tune the properties of these systems with ion implantation, we present a study of the…
Here we report mid infrared (mid-IR) photothermal response of multi layer MoS2 thin film grown on crystalline (p-type silicon and c-axis oriented single crystal sapphire) and amorphous substrates (Si/SiO2 and Si/SiN) by pulsed laser…