Related papers: Upper efficiency limit of Sb2Se3 solar cells
Solar modules are currently characterized at standard test conditions (STC), defined at 1000W/m2 and 25 {\deg}C. However, solar modules in actual outdoor operating conditions typically operate at lower illumination and higher temperature…
Halide perovskites excel in the pursuit of highly efficient thin film photovoltaics, with power conversion efficiencies reaching 25.5% in single junction and 29.5% in tandem halide perovskite/silicon solar cell configurations. Operational…
The Shockley-Queisser (S-Q) theory defines the thermodynamic upper limits for Jsc, Voc, FF, and efficiency of a solar cell. The classical calculation assumes an abrupt onset of absorption at the band-edge, perfect absorption for all…
Two-dimensional (2D) layered lead iodide (PbI2) is an important precursor and common residual species during the synthesis of lead-halide perovskites. There currently exist some debates and uncertainties about the effect of excess PbI2 on…
The honeycomb connection of carbon atoms by covalent bonds in a macroscopic two-dimensional scale leads to fascinating graphene and solar cell based on graphene/silicon Schottky diode has been widely studied. For solar cell applications,…
Modern photovoltaic devices are often based on a heterojunction structure where two components with different optoelectronic properties are interfaced. The properties of each side of the junction can be tuned by either utilizing different…
Polymer solar cells are considered as very promising candidates for development of photovoltaics of the future. They are cheap and easy to fabricate, however, up to now, they possess fundamental drawback, low effectiveness. In the most…
Theoretically and experimentally we have proved the existence of optimal thickness of the porous layer used as an anti-reflection coating in solar cells. We have taken into account the joint mechanisms of generation and recombination of…
Quaternary mixed-metal chalcohalides (Sn$_2$BCh$_2$X$_3$) are emerging as promising lead-free perovskite-inspired photovoltaic absorbers. Motivated by recent developments of a first Sn$_2$BCh$_2$X$_3$-based device, we used density…
Hybrid halide perovskites are currently under intense investigation due to their potential applications in optoelectronics and solar cells. Among them, MAPbI$_3$ where MA stands for the methylammonium cation, exhibits ideal properties for…
Lead-free all-inorganic halide perovskite solar cells (PSCs) have emerged as a promising alternative to toxic lead-based solar cells and organic solar cells, which have limited stability. This work explores such a PSC with sodium tin…
We introduce a limit for the strength of coupling light into the modes of solar cells. This limit depends on both a cell's thickness and its modal properties. For a cell with refractive index n and thickness d, we obtain a maximal coupling…
Photon impingement is capable of liberating electrons in semiconductors. When the electron transport is primarily governed by temperature gradients, high irreversibilities will result, thus lowering converters' efficiencies. A fundamental…
Cu(In,Ga)Se2 based solar cells exceed power conversion efficiencies of 23 %. Yet, the fill factor of these solar cells, with best values around 80 %, is relatively low (Si reaches 84.9%) mostly due to diode factors greater than one.…
The present article reports a comprehensive energy balance analysis of a photon-enhanced thermionic emission (PETE) device when it is used for concentrated solar power (CSP) generation. To this end, we consider a realistic PETE device…
Detailed-balance limits for transition-metal dichalcogenide (TMD) solar cells have been reported, but existing TMD-specific limits do not simultaneously resolve thickness-dependent optics, carrier multiplication (CM), hot-carrier (HC)…
Selenium is experiencing renewed interest as a promising candidate for the wide bandgap photoabsorber in tandem solar cells. However, despite the potential of selenium-based tandems to surpass the theoretical efficiency limit of single…
We conduct a comprehensive assessment of the electronic and optical properties, as well as photovoltaic (PV) performance parameters for Mg$_{2}$Si and Ca$_{2}$Si using density-functional theory and Bethe-Salpeter equation (BSE) based…
The decrease of solar cell efficiency with temperature is a known problem for photovoltaics (PV). Temperature sensitivity can lead to a considerable amount of energy losses over the lifetime of solar panels. In this perspective Hybrid…
Antimony sulfide (Sb$_2$S$_3$), a compound of earth-abundant elements with highly anisotropic, quasi-layered crystal structure, triggered growing interest as a solar absorber in photovoltaics and as a phase change material in memory…