Related papers: Grain-level effects on in-situ deformation-induced…
Three-dimensional X-ray diffraction (3DXRD) has been used to measure, in-situ, the evolution of $\sim 1800$ grains in a single phase low carbon ferritic steel sample during uniaxial deformation. The distribution of initial residual grain…
In this study, the effect of ferrite grain size on the mechanical properties and dislocation behavior of dual-phase (DP) steel is investigated using dislocation-based crystal plasticity finite element analysis. DP steel, composed of a soft…
A multi-phase field model is employed to study the microstructural evolution of an alloy undergoing liquid dealloying. The model proposed extends upon the original approach of Geslin et al. to consider dealloying in the presence of grain…
An original thermodynamically consistent large strains-based multiphase phase-field (PF) approach of Ginzburg-Landau type is developed for studying the grain boundary (GB)-induced martensitic transformations (MTs) in polycrystalline…
Deformation heterogeneities within microstructures of polycrystalline shape memory alloys (SMAs) during superelastic stressing are studied using both experiments and simulations. In situ X-ray diffraction, specifically the far-field high…
This work explains the occurrence of transformation-induced plasticity via stress-assisted martensite, when designing ultrafine-grained duplex steels. It is found that, when the austenite is reduced to a fine scale of about 300 nm, the…
Near-field and far-field high-energy diffraction microscopy and microcomputed tomography X-ray techniques were used to study a bulk single crystal nickel-titanium shape memory alloy sample subjected to thermal cycling under a constant…
The industrialization of Laser Additive Manufacturing (LAM) is challenged by the undesirable microstructures and high residual stresses originating from the fast and complex solidification process. Non-destructive assessment of the…
Phase-field simulations of the martensitic transformation (MT) in the austenitic matrix, which has already undergone the plastic deformation, are carried out. For this purpose the elasto-plastic phase-field approach of incoherent MT…
A phase-field model is developed to simulate intergranular corrosion of ferritic/martensitic steels exposed to liquid lithium. The chromium concentration of the material is used to track the mass transport within the metal and liquid…
Grain growth is a key process in the thermomechanical treatment of metals. Recently, the presence of local residual stresses within fully recrystallized grains has attracted increasing interest in connection with shear-coupled grain…
A novel concept of varying the strain hardening rate of a medium Mn steel with 8 wt\% Mn by varying the duration of the intercritical anneal after hot rolling was explored. It was found that the stability of the austenite phase showed an…
Bio-cementation uses bacterially induced calcite to bind sand grains, offering a low-carbon approach to soil stabilization. However, the 3D morphology, orientation texture, and internal strain states of individual calcite bonds remain…
In situ neutron diffraction of the uniaxial tension test was used to study the effect of the surrounding matrix microstructure on the mechanical stability of retained austenite in high-carbon bearing steels. Comparing the samples with…
High performance sheet metals with a multi-phase microstructure suffer from deformation induced damage formation during forming in the constituent phases but importantly also where these intersect. To capture damage in terms of the physical…
The ability to characterise the three-dimensional microstructure of multiphase materials is essential for understanding the interaction between phases and associated materials properties. Here, laboratory-based diffraction-contrast…
Strength, ductility, and failure properties of metals are tailored by plastic deformation routes. Predicting these properties requires modeling of the structural dynamics and stress evolution taking place on several length scales. Progress…
Atomistically-informed phase field simulations have been performed to investigate the effect of five common alloying elements (Nb, Ti, Mo, V, Mn) on austenite grain growth. The anisotropic simulations based on the segregation energy…
Additive manufacturing of Ti-6Al-4V alloy via laser powder-bed fusion leads to non-equilibrium $\alpha'$ martensitic microstructures, with high strength but poor ductility and toughness. These properties may be modified by heat treatments,…
In this study, we employ high-energy X-ray characterization to examine the role of relatively large amounts of intragranular lattice misorientation -- present after many thermomechanical processes -- on the micromechanical response of…