Related papers: The ATLAS Readout System for LHC Runs 2 and 3
The DZERO experiment located at Fermilab has recently started RunII with an upgraded detector. The RunII physics program requires the Data Acquisition to readout the detector at a rate of 1 KHz. Events fragments, totaling 250 KB, are…
Triggering on hadronic tau decays is essential for a wide variety of analyses of interesting physics processes at ATLAS. The ATLAS tau trigger combines information from the tracking detectors and calorimeters to identify the signature of…
Planned upgrades of the LHC over the next decade should allow the machine to operate at a center of mass energy of 14 TeV with instantaneous luminosities in the range 5--7e34 cm^-2 s^-1. With these parameters, ATLAS could collect 3,000…
In 2019, the LHCb experiment at CERN will undergo a major upgrade where its detector electronics and the entire readout system will be replaced. The goal is to read-out all events at the full LHC frequency of 40 MHz, reaching a total data…
The factor of four increase in the LHC luminosity, from $0.5\times 10^{34}\,\textrm{cm}^{-2}\textrm{s}^{-1}$ to $2.0\times 10^{34}\textrm{cm}^{-2}\textrm{s}^{-1}$, and the corresponding increase in pile-up collisions during the 2015-2018…
During the upcoming Run 3 and Run 4 at the LHC the upgraded ALICE (A Large Ion Collider Experiment) will operate at a significantly higher luminosity and will collect two orders of magnitude more events than in Run 1 and Run 2. A part of…
Among the many challenges presented by the future ATLAS detector at the LHC are the high data taking rate and volume and the derivation of a rapid trigger decision with limited resources. To address this challenge within the ATLAS second…
The ATLAS trigger has been used very successfully to collect collision data during 2009 and 2010 LHC running at centre of mass energies of 900 GeV, 2.36 TeV, and 7 TeV. This paper presents the ongoing work to commission the ATLAS trigger…
The ATLAS Semiconductor Tracker (SCT) together with the pixel and the transition radiation detectors will form the tracking system of the ATLAS experiment at LHC. It will consist of 20000 single-sided silicon microstrip sensors assembled…
ATLAS, a general-purpose experiment at the Large Hadron Collider (LHC), makes use of a large internationally-distributed computing infrastructure, including over $10^6$ TB of managed data on disk and tape and almost one million…
ALICE is one of the four experiments at the CERN Large Hadron Collider (LHC) specifically designed to study nuclear matter at extreme conditions of temperature and pressure. The LHC Run 3 started officially in July 2022 with proton-proton…
Proton-proton collisions at sqrt{s} = 7 TeV and heavy ion collisions at sqrt{s_NN} = 2.76 TeV were produced by the LHC and recorded using the ATLAS experiment's trigger system in 2010. The LHC is designed with a maximum bunch crossing rate…
During 2015 the ATLAS experiment recorded 3.8 fb$^{-1}$ of proton--proton collision data at a centre-of-mass energy of 13 TeV. The ATLAS trigger system is a crucial component of the experiment, responsible for selecting events of interest…
Current and future experiments at the high intensity frontier are expected to produce an enormous amount of data that needs to be collected and stored for offline analysis. Thanks to the continuous progress in computing and networking…
Run-2 of the Large Hadron Collider (LHC) will provide new challenges to track and vertex reconstruction with higher energies, denser jets and higher rates. Therefore the ATLAS experiment has constructed the first 4-layer Pixel Detector in…
The ATLAS experiment relies on real-time hadronic jet reconstruction and $b$-tagging to record fully hadronic events containing $b$-jets. These algorithms require track reconstruction, which is computationally expensive and could overwhelm…
This article describes the design, testing and production of the ATLAS Region of Interest Builder (RoIB). This device acts as an interface between the Level 1 trigger and the high level trigger (HLT) farm for the ATLAS LHC detector. It…
The Tile Calorimeter (TileCal) is one detector of the ATLAS experiment at the Large Hadron Collider (LHC). TileCal is a sampling calorimeter made of steel plates and plastic scintillators which are readout using approximately 10,000…
The Robot Operating System 2 (ROS2) targets distributed real-time systems and is widely used in the robotics community. Especially in these systems, latency in data processing and communication can lead to instabilities. Though being highly…
The High Luminosity Large Hadron Collider (HL-LHC) at CERN is expected to collide protons at a centre-of-mass energy of 14\,TeV and to reach the unprecedented peak instantaneous luminosity of 5\,$-$\,7.5\,x\,$10^{34}$\,cm$^{-2}$s$^{-1}$…