Related papers: Slip intermittency and dwell fatigue in titanium a…
Dwell fatigue, the reduction in fatigue life experienced by titanium alloys due to holds at stresses as low as 60% of yield, has been implicated in several uncontained jet engine failures. Dislocation slip has long been observed to be an…
Plasticity in hexagonal close packed (HCP) metals and alloys such as Titanium (Ti) and Zirconium (Zr) is carried out by the motion of $\langle a \rangle$ dislocations. Above room temperature, in situ transmission electron microscopy…
The dislocation structures appearing in highly mis-oriented soft/hard grain pairs in near-alpha titanium alloy Ti6242Si were examined with and without the application of load holds (dwell) during fatigue. Dislocation pile-up in a soft grain…
There is a long-standing technological problem in which a stress dwell during cyclic loading at room temperature in Ti causes a significant fatigue life reduction. It is thought that localised time dependent plasticity in soft grains…
Plasticity in hexagonal close-packed zirconium is controlled by screw dislocations which easily glide in the prismatic planes where they are dissociated. At high enough temperatures, these dislocations can deviate out of the prism planes to…
Basal slip acts as a secondary deformation mode in hexagonal close-packed titanium and becomes one of the primary mechanisms in titanium alloyed with simple metals. As these solute elements also lead to a pronounced reduction of the energy…
There is a long standing technological problem in which a stress dwell during cyclic loading at room temperature in Ti causes a significant fatigue life reduction. It is thought that localised time dependent plasticity in soft grains…
Plasticity in zirconium is controlled by 1/3<1-210> screw dislocations gliding in the prism planes of the hexagonal close-packed structure. This prismatic and not basal glide is observed for a given set of transition metals like zirconium…
The interaction between screw dislocations and oxygen interstitial atoms is studied with ab initio calculations in hexagonal close-packed titanium. Our calculations evidence a strong repulsion when the solute atoms are located in the…
Component failure due to cold dwell fatigue of titanium and its alloys is a long-standing problem which has significant safety and economic implications to the aviation industry. This can be addressed by understanding the governing…
The classical motion of gliding dislocation lines in slip planes of crystalline solid helium leads to plastic deformation even at temperatures far below the Debye temperature and can affect elastic properties. In this work we argue that the…
Plasticity in zirconium alloys is mainly controlled by the interaction of 1/3 1210 screw dislocations with oxygen atoms in interstitial octahedral sites of the hexagonal close-packed lattice. This process is studied here using ab initio…
A phase field model is presented to investigate dislocation formation (coherency loss) and workhardening in two-phase binary alloys. In our model the elastic energy density is a periodic function of the shear and tetragonal strains, which…
Here we analyze a three-dimensional distribution of crystallographic slip measured in-situ during the uniaxial deformation of hexagonal Ti-7Al. The slip field is reconstructed using a novel methodology that combines spatially resolved…
Discrete dislocation plasticity (DDP) calculations are carried out to investigate the response of a single crystal contacted by a rigid sinusoidal asperity under sliding loading conditions to look for causes of microstructure change in the…
We investigate dilation-induced surface deformations in a Discontinuous Shear Thickening (DST) suspension to determine the relationship between dilation and stresses in DST. Video is taken at two observation points on the surface of the…
Here we present a model to study the micro-plastic regime of a stress-strain curve. In this model an explicit dislocation population represents the mobile dislocation content and an internal shear-stress field represents a mean-field…
The viscoplastic deformation (creep) of crystalline materials under constant stress involves the motion of a large number of interacting dislocations. Analytical methods and sophisticated `dislocation-dynamics' simulations have proved very…
During plastic deformation, metals change shape while continuously becoming stronger. The microscopic origin of these processes lies in the proliferation and movement of line defects, dislocations, and the subsequent self-organisation and…
The yield surface in crystal plasticity can be approached from various directions during mechanical loading. We consider the competition between nanoindentation and tensile loading towards plastic yielding. For this purpose, we develop a…