Related papers: Numerical modeling of CuSbSe2-based dual-heterojun…

The p-type amorphous/ n-type crystalline silicon (P+ a-Si/N+ c-Si) heterojunction was simulated for developing the solar cells with high conversion efficiency and low cost. The characteristic of such cells with different work function of…

The Shockley and Queisser limit, a well-known efficiency limit for a solar cell, is based on unrealistic physical assumptions and its maximum limit is seriously overestimated. To understand the power loss mechanisms of record-efficiency…

Practical device architectures are proposed here for the implementation of three-terminal heterojunction bipolar transistor solar cells (3T-HBTSCs). These photovoltaic devices, which have a potential efficiency similar to that of…

Sulfide chalcopyrite Cu(In,Ga)S2 (CIGS) is a wide bandgap semiconductor suitable for the top cell of a tandem solar device. Here we demonstrate significant improvements in absorber quality by alloying with Ag to form (Ag,Cu)(In,Ga)S2…

The transition to sustainable energy has accelerated research into perovskite solar cells (PSCs) as promising candidates for next-generation photovoltaics. Despite their remarkable efficiencies, the commercialization of PSCs is hindered by…

Two-dimensional transition metal dichalcogenides (TMDCs) have recently attracted attention due to their superlative optical and electronic properties. In particular, their extraordinary optical absorption and semiconducting band gap have…

$CuGa_3Se_5$ is a promising candidate material with wide band gap for top cells in tandem photovoltaic (PV) and photoelectrochemical (PEC) devices. However, traditional CdS contact layers used with other chalcopyrite absorbers are not…

Two strategies for enhancing photovoltaic (PV) performance in chalcopyrite solar cells were investigated: Cu1-xKxIn1-yGaySe2 absorbers with low K content (K/(K+Cu), or x ~ 0.07) distributed throughout the bulk, and CuIn1-yGaySe2 absorbers…

We demonstrate a non-destructive approach to provide structural properties on the grain level for the absorber layer of kesterite solar cells. Kesterite solar cells are notoriously difficult to characterize structurally due to the…

Materials research with a focus on enhancing the minority-carrier lifetime of the light-absorbing semiconductor is key to advancing solar energy technology for both early-stage and mature material platforms alike. Tin sulfide (SnS) is an…

The widespread use of lead-based materials in tandem solar cells raises critical environmental and health concerns due to their inherent toxicity and risk of contamination. To address this challenge, we focused on lead-free tandem…

The purpose of this work is to look for a practical structure for application of quantum dots (QD) in solar cells in order to enhance sub-band gap photon absorption. We focuse on a stack of strain-compensated GaSb/GaAs type-II QDs. We…

Solar modules are currently characterized at standard test conditions (STC), defined at 1000W/m2 and 25 {\deg}C. However, solar modules in actual outdoor operating conditions typically operate at lower illumination and higher temperature…

Cu2ZnSnS4 (CZTS) is a promising candidate as an absorber material for thin film solar cells. The reported wet chemical synthesis approaches often have a high environmental impact due to the usage of abrasive solvents such as hydrazines,…

Solution-processed quantum dots (QDs) have a high potential for fabricating low cost, flexible and large-scale solar energy harvesting devices. It has recently been demonstrated that hybrid devices employing a single monovalent cation…

The development of tandem photovoltaics and photoelectrochemical solar cells requires new absorber materials with band gaps in the range of ~1.5-2.3 eV, for use in the top cell paired with a narrower-gap bottom cell. An outstanding…

Traditional CdS buffer layer in selenium-free Cu(In,Ga)S2 solar cells leads to reduced open-circuit voltage because of a negative conduction band offset at the Cu(In,Ga)S2/CdS interface. Reducing this loss necessitates the substitution of…

Antimony sulfide (Sb2S3) is a promising candidate as an absorber layer for single-junction solar cells and the top subcell in tandem solar cells. However, the power conversion efficiency of Sb2S3-based solar cells has remained stagnant over…

Sulfide Kesterite Cu2ZnSnS4 (CZTS), a nontoxic and low-cost photovoltaic material, has always being facing severe charge recombination and poor carrier transport, resulting in the cell efficiency record stagnating around 11% for years.…

Aqueous precursors provide an alluring approach for low-cost and environmentally friendly production of earth-abundant Cu2ZnSn(S,Se)4 (CZTSSe) solar cells. The key is to find an appropriate molecular agent to prepare a stable solution and…